AMS2911
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Load Regulation
(Notes 2, 3)
AMS2911-3.3
AMS2911-5.0
Dropout Voltage
(V
IN
-
V
OUT
)
Current Limit
Minimum Load
Current
Quiescent Current
Ripple Rejection
AMS2911-1.5/-1.8/-2.5/-
2.85/ -3.3/-5.0
AMS2911-1.5/-1.8/-2.5/-
2.85/ -3.3/-5.0
AMS2911
AMS2911-1.5/-1.8/-2.5/-
2.85/ -3.3/-5.0
AMS2911
AMS2911-1.5/-1.8/-2.5/-
2.85
AMS2911-3.3
AMS2911-5
Thermal Regulation
Adjust Pin Current
Adjust Pin Current
Change
Temperature Stability
Long Term Stability
RMS Output Noise
(% of V
OUT
)
Thermal Resistance
Junction-to-Case
M Package: Control Circuitry/ Power Transistor
T Package: Control Circuitry/ Power Transistor
1.5/4.0
1.5/4.0
°C/W
°C/W
T
A
=125°C, 1000Hrs
T
A
= 25°C , 10Hz
≤
f
≤
10kHz
AMS2911
AMS2911
AMS2911
V
IN
= 5V, 0
≤
I
OUT
≤
1A
V
IN
= 8V, 0
≤
I
OUT
≤
1A
∆V
OUT
,
∆V
REF
= 1%, I
OUT
= 1A (Note 4)
(V
IN
- V
OUT
) = 5V
(V
IN
- V
OUT
) = 12V (Note 5)
V
IN
≤
12V
.9
Device
AMS2911-2.85
Conditions
V
IN
= 5V, 0
≤
I
OUT
≤
1A
Min
Typ
3
6
3
7
5
10
1.3
1.1
5
5
Max
12
20
15
25
20
35
1.5
1.5
10
10
Units
mV
mV
mV
mV
mV
mV
V
A
mA
mA
dB
dB
dB
dB
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1A,
(V
IN
-V
OUT
) = 3V, C
ADJ
=25µF
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1A,
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1A
V
IN
= 6.3V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1A
V
IN
= 8V
T
A
= 25°C, 30ms pulse
10mA
≤
I
OUT
≤
1A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
10mA
≤
I
OUT
≤
1A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
60
60
60
60
75
72
72
68
0.008
55
120
0.2
0.5
0.3
0.003
1
5
0.04
%W
µA
µA
µA
%
%
%
Parameters identified with
boldface type
apply over the full operating temperature range.
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics
.
The guaranteed specifications apply only for the test conditions listed.
Note 2:
Line and Load regulation are guaranteed up to the maximum power dissipation of 1.2W. Power dissipation is determined by the input/output
differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
Dropout voltage is specified over the full output current range of the device.
Note 5:
Minimum load current is defined as the minimum output current required to maintain regulation. When 1.5
≤
(V
IN
- V
OUT
)
≤12V
the device is
guaranteed to regulate if the output current is greater than 10mA.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
ADMOS [ ADVANCED MONOLITHIC SYSTEMS ]
