z
Absolute Maximum Ratings
Parameter
Symbol
TC
Range
Units
°C
-55 to +125
-65 to +150
-2.0 to +7.0
Case Operating Temperature
Storage Temperature Range
Supply Voltage Range
TSTG
VCC
°C
V
VG
-2.0 to +7.0
300
V
°C
Signal Voltage Range (Any Pin Except A9) Note 1
Maximum Lead Temperature (10 seconds)
Data Retention
-
-
10
Years
-
100,000 Minimum
-2.0 to +14.0
Endurance (Write/Erase cycles)
A9 Voltage for sector protect, Note 2
VID
V
Note 1. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may undershoot VSS to -2.0v for periods of up to
20ns. Maximum DC voltage on input and I/O pins is VCC + 0.5V. During voltage transitions, inputs and I/O pins may overshoot to
VCC + 2.0V for periods up to 20 ns.
Note 2. Minimum DC input voltage on A9 is -0.5V. During voltage transitions, A9 may undershoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 is +12.5V which may overshoot to 14.0V for periods up to 20ns.
Normal Operating Conditions
A
Symbol Parameter
Minimum
Maximum
Units
VCC
VIH
VIL
TA
+4.5
+5.5
V
Power Supply Voltage
Input High Voltage
+2.0
-0.5
-55
V
+ 0.5
V
V
CC
+0.8
Input Low Voltage
+125
12.5
°C
V
Operating Temperature (Military)
A9 Voltage for sector protect
VID
11.5
Capacitance
(VIN= 0V, f = 1MHz, Tc = 25°C)
Symbol Parameter
Maximum
Units
CAD
COE
CWE
50
50
pF
pF
A0 – A16 Capacitance
OE Capacitance
Write Enable Capacitance
CQFP(F5) Package
20
20
20
20
pF
pF
pF
pF
PGA(P3,P7) Package
Chip Enable Capacitance
I/O0 – I/O31 Capacitance
CCE
CI/O
Parameters Guaranteed but not tested
DC Characteristics – CMOS Compatible
(Vcc = 5.0V, Vss = 0V, TC = -55°C to +125°C, unless otherwise indicated)
Speeds 60, 70, 90, 120 & 150ns
Parameter
Sym
Conditions
Minimum
Maximum
Units
ILI
ILOX32
ICC1
ICC2
ICC4
ICC3
VOL
10
µA
Input Leakage Current
VCC = 5.5V, ViN = GND to VCC
VCC = 5.5V, ViN = GND to VCC
CE = VIL, OE = VIH, f = 5MHz
CE = VIL, OE = VIH
10
190
240
6.5
µA
mA
mA
mA
mA
V
Output Leakage Current
Active Operating Supply Current for Read (1)
Active Operating Supply Current for Program or Erase (2)
Standby Supply Current
VCC = 5.5V, CE = VIH, f = 5MHz
VCC = 5.5V, CE = VIH
0.6
Static Supply Current (4)
0.45
Output Low Voltage
IOL = +8.0 mA, VCC = 4.5V
IOH = –2.5 mA, VCC = 4.5V
VOH
0.85 x VCC
3.2
V
Output High Voltage
VLKO
4.2
V
Low Power Supply Lock-Out Voltage (4)
Note 1. The Icc current listed includes both the DC operating current and the frequency dependent component (At 5 MHz). The frequency
component typically is less than 2 mA/MHz, with OE at VIN.
Note 2. Icc active while Embedded Algorithm (Program or Erase) is in progress.
Note 3. DC Test conditions: VIL = 0.3V, VIH = VCC - 0.3V, unless otherwise indicated
Note 4. Parameter Guaranteed but not tested.
3
Aeroflex Circuit Technology
SCD1665 REV B 6/29/01 Plainview NY (516) 694-6700
AEROFLEX [ AEROFLEX CIRCUIT TECHNOLOGY ]
