欢迎访问ic37.com |
会员登录 免费注册
发布采购

LUCL9215GAU-D 参数 Datasheet PDF下载

LUCL9215GAU-D图片预览
型号: LUCL9215GAU-D
PDF下载: 下载PDF文件 查看货源
内容描述: 短环正弦波振铃SLIC [Short-Loop Sine Wave Ringing SLIC]
分类和应用:
文件页数/大小: 50 页 / 1068 K
品牌: AGERE [ AGERE SYSTEMS ]
 浏览型号LUCL9215GAU-D的Datasheet PDF文件第2页浏览型号LUCL9215GAU-D的Datasheet PDF文件第3页浏览型号LUCL9215GAU-D的Datasheet PDF文件第4页浏览型号LUCL9215GAU-D的Datasheet PDF文件第5页浏览型号LUCL9215GAU-D的Datasheet PDF文件第6页浏览型号LUCL9215GAU-D的Datasheet PDF文件第7页浏览型号LUCL9215GAU-D的Datasheet PDF文件第8页浏览型号LUCL9215GAU-D的Datasheet PDF文件第9页  
Data Sheet
September 2001
L9215A/G
Short-Loop Sine Wave Ringing SLIC
Introduction
The Agere Systems Inc. L9215 is a subscriber line
interface circuit that is optimized for short-loop,
power-sensitive applications. This device provides
the complete set of line interface functionality (includ-
ing power ringing) needed to interface to a subscriber
loop. This device has the capability to operate with a
V
CC
supply of 3.3 V or 5 V and is designed to mini-
mize external components required at all device
interfaces.
Applications
s
s
s
s
s
s
s
Voice over Internet Protocol (VoIP)
Cable Modems
Terminal Adapters (TA)
Wireless Local Loop (WLL)
Telcordia Technologies
GR-909 Access
Network Termination (NT)
Key Systems
Features
s
s
Onboard ringing generation
Three ringing input options:
— Sine wave
— PWM
— Logic level square wave
Flexible V
CC
options:
— 5 V or 3.3 V V
CC
— No –5 V required
Battery switch to minimize off-hook power
11 operating states:
— Scan mode for minimal power dissipation
— Forward and reverse battery active
— On-hook transmission states
— Meter pulse states
— Ring mode
— Disconnect mode
Ultralow on-hook power:
— 27 mW scan mode
— 42 mW active mode
Two SLIC gain options to minimal external compo-
nents in codec interface
Loop start, ring trip, and ground key detectors
Software- or hardware-controllable current-limit
and overhead voltage
Meter pulse compatible
32-pin PLCC package
48-pin MLCC package
Description
This device is optimized to provide battery feed, ring-
ing, and supervision on short-loop plain old tele-
phone service (POTS) loops.
This device provides power ring to the subscriber
loop through amplification of a low-voltage input. It
provides forward and reverse battery feed states, on-
hook transmission, a low-power scan state, meter
pulse states, and a forward disconnect state.
The device requires a V
CC
and battery to operate.
V
CC
may be either a 5 V or a 3.3 V supply. The ring-
ing signal is derived from the high-voltage battery. A
battery switch is included to allow for use of a lower-
voltage battery in the off-hook mode, thus minimizing
short-loop off-hook power.
Loop closure, ring trip, and ground key detectors are
available. The loop closure detector has a fixed
threshold with hysteresis. The ring trip detector
requires a single-pole filter, thus minimizing external
components required.
This device supports meter pulse applications. Meter
pulse is injected into a dedicated meter pulse input.
Injection of meter pulse onto tip and ring is controlled
by the device’s logic input pin.
Both the dc current limit and overhead voltage are
programmable. Programming may be done by exter-
nal resistors or an applied voltage source. If the volt-
age source is programmable, the current limit and
overhead may be set via software control.
The device is offered with two gain options. This
allows for an optimized codec interface, with minimal
external components regardless of whether a first-
generation or a programmable third-generation
codec is used.
s
s
s
s
s
s
s
s
s
s