Package Characteristics
Over Recommended Temperature (T
A
= 0˚C to 70˚C) unless otherwise specified.
Parameter
Sym. Device
Min. Typ.* Max.
Units Test Conditions
Input-Output
V
ISO
8-Pin DIP
3750
V rms RH < 50%,
Momentary
SO-8
t = 1 min.,
Withstand
T
A
= 25˚C
Voltage**
I
I-O
8-Pin DIP
1
µA
45% RH, t = 5 s,
V
I-O
= 3 kVdc,
T
A
= 25˚C
Input-Output
R
I-O
8-Pin DIP
10
12
Ω
V
I-O
= 500 Vdc
Resistance
SO-8
Input-Output
C
I-O
8-Pin DIP
0.6
pF
f = 1 MHz
Capacitance
SO-8
Fig.
Note
6, 14
6, 16
6
6
*All typicals at T
A
= 25˚C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable),
your equipment level safety specification or Agilent Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage," publication
number 5963-2203E.
Notes:
1. Derate linearly above 70˚C free-air temperature at a rate of 0.8 mA/˚C (8-Pin DIP).
Derate linearly above 85˚C free-air temperature at a rate of 0.5 mA/˚C (SO-8).
2. Derate linearly above 70˚C free-air temperature at a rate of 1.6 mA/˚C (8-Pin DIP).
Derate linearly above 85˚C free-air temperature at a rate of 1.0 mA/˚C (SO-8).
3. Derate linearly above 70˚C free-air temperature at a rate of 0.9 mW/˚C (8-Pin DIP).
Derate linearly above 85˚C free-air temperature at a rate of 1.1 mW/˚C (SO-8).
4. Derate linearly above 70˚C free-air temperature at a rate of 2.0 mW/˚C (8-Pin DIP).
Derate linearly above 85˚C free-air temperature at a rate of 2.3 mW/˚C (SO-8).
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
O
, to the forward LED input current, I
F
, times 100.
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
CM
/dt on the leading edge of the common
mode pulse signal, V
CM
, to assure that the output will remain in a Logic High state (i.e., V
O
> 2.0 V). Common mode transient immunity in a
Logic Low level is the maximum tolerable (negative) dV
CM
/dt on the trailing edge of the common mode pulse signal, V
CM
, to assure that the
output will remain in a Logic Low state (i.e., V
O
< 0.8 V).
8. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 mA kΩ pull-up resistor.
9. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.
10. The frequency at which the AC output voltage is 3 dB below its mid-frequency value.
11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 15%.
12. See Option 020 data sheet for more information.
13. Use of a 0.1
µf
bypass capacitor connected between pins 5 and 8 is recommended.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
≥
4500 V rms for 1 second (leakage
detection current limit, I
I-O
≤
5
µA).
This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
Related Characteristics Table, if applicable.
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
≥
6000 V rms for 1 second (leakage
detection current limit, I
I-O
≤
5
µA).
This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
Related Characteristics Table, if applicable.
16. This rating is equally validated by an equivalent AC proof test.
8
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
