欢迎访问ic37.com |
会员登录 免费注册
发布采购

HSSR-8400 参数 Datasheet PDF下载

HSSR-8400图片预览
型号: HSSR-8400
PDF下载: 下载PDF文件 查看货源
内容描述: 400 V / 10欧姆,通用,1个A型,固态继电器 [400 V/10 Ohm, General Purpose, 1 Form A, Solid State Relay]
分类和应用: 继电器固态继电器
文件页数/大小: 13 页 / 261 K
品牌: AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
 浏览型号HSSR-8400的Datasheet PDF文件第2页浏览型号HSSR-8400的Datasheet PDF文件第3页浏览型号HSSR-8400的Datasheet PDF文件第4页浏览型号HSSR-8400的Datasheet PDF文件第5页浏览型号HSSR-8400的Datasheet PDF文件第6页浏览型号HSSR-8400的Datasheet PDF文件第7页浏览型号HSSR-8400的Datasheet PDF文件第8页浏览型号HSSR-8400的Datasheet PDF文件第9页  
H
400 V/10 Ohm,
General Purpose, 1 Form A,
Solid State Relay
Technical Data
HSSR-8400
Features
• Compact Solid-State
Bidirectional Switch
• Normally-Off Single-Pole
Relay Function (1 Form-A)
• 400 V Output Withstand
Voltage in Both Polarities at
25
°
C
• 150/300 mA Current Ratings
(See Schematic for
Connection A & B)
• Low Input Current; CMOS
Compatibility
• Very Low On-Resistance: 6
Typical at 25
°
C
• ac/dc Signal & Power
Switching
• Input-to-Output Momentary
Withstand Insulation
Voltage: 2500 Vac, 1 Minute
• 16-kV ESD Immunity: MIL-
STD-883, Method 3015
• CSA Approved
• UL 508 Recognized
Description
The HSSR-8400 consists of a
high-voltage circuit, optically
coupled with a Light-Emitting
Diode (LED). This device is a
solid-state replacement for single-
pole, normally-open (1 Form A)
electromechanical relays used for
general purpose switching of
signals and low-power ac/dc
loads. The relay turns on (contact
closes) with a minimum input
current, I
F
, of 5 mA through the
input LED. The relay turns off
(contact opens) with an input
voltage, V
F
, of 0.8 V or less. The
detector contains a high speed
photosensitive FET driver circuit
and two high voltage MOSFETs.
This relay’s logic-level input con–
trol and very low typical output
on-resistance of 6
make it
suitable for switching of audio
frequency signals in telecom
applications. Connection A, as
shown in the schematic, allows
the relay to switch either ac or dc
loads. In this configuration, the
150 mA output current rating
allows it to switch small loads
that are driven from 110 Vac and
220 Vac power lines. Connection
B, with the polarity and pin
configuration as indicated in the
schematic, allows the relay to
switch dc loads only. The
advantage of Connection B is that
the on-resistance is significantly
reduced and the output current
capability increases by a factor of
two.
The electrical and switching
characteristics of the HSSR-8400
are specified from -40°C to
+85°C.
Functional Diagram
Applications
• Modems
• Telecommunication
Switching Equipment
• Telecommunication Test
Instruments
• Reed Relay Replacement
• 110/220 Vac Load Driver
• Industrial Relay Coil Driver
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
OUTPUT
L
H
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
1-465
5965-3573E