INA-52063 Typical Scattering Parameters[3],TC = 25°C, ZO = 50 Ω, VCC = 5.0 V
Freq.
GHz
S11
S21
Mag
S12
Mag
S22
K
Mag
Ang
dB
Ang
dB
Ang
Mag
Ang
Factor
0.05
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.60
2.80
3.00
0.06
0.06
0.06
0.07
0.07
0.09
0.10
0.12
0.13
0.15
0.17
0.21
0.24
0.27
0.30
0.32
0.33
0.35
0.36
0.36
0.36
165
154
131
104
80
66
46
30
14
23.5
23.4
23.4
23.3
23.1
23.0
22.8
22.6
22.3
22.0
21.7
21.0
20.2
19.4
18.6
17.8
17.1
16.3
15.5
14.8
14.1
14.88
14.84
14.72
14.57
14.33
14.08
13.76
13.41
13.01
12.59
12.14
11.22
10.28
9.38
8.55
7.80
7.13
6.52
5.98
5.52
5.08
-5
-9
-19
-28
-37
-46
-55
-64
-29.3
-29.3
-29.4
-29.5
-29.4
-29.4
-29.4
-29.3
-29.2
-29.0
-28.8
-28.4
-28.1
-27.7
-27.5
-27.4
-27.6
-27.8
-28.1
-28.9
-29.5
0.034
0.034
0.034
0.034
0.034
0.034
0.034
0.034
0.035
0.036
0.036
0.038
0.040
0.041
0.042
0.043
0.042
0.041
0.039
0.036
0.033
0
0
0
1
2
3
4
5
6
6
7
7
6
4
2
0.05
0.05
0.05
0.06
0.07
0.08
0.09
0.11
0.13
0.14
0.16
0.20
0.23
0.25
0.27
0.29
0.30
0.31
0.32
0.33
0.33
1
0
-1
-5
1.24
1.24
1.25
1.25
1.26
1.27
1.28
1.29
1.28
1.27
1.28
1.25
1.24
1.26
1.29
1.33
1.44
1.56
1.74
2.01
2.37
-10
-14
-21
-29
-37
-45
-52
-67
-81
-94
-107
-118
-129
-139
-149
-158
-168
-73
-82
-90
0
-12
-33
-50
-66
-80
-93
-105
-117
-128
-139
-149
-106
-122
-137
-151
-164
-177
170
159
147
136
-1
-5
-8
-12
-15
-16
Note: 3. Reference plane per Figure 9 in Applications Information section.
INA-52063 Applications
Information
Introduction
SOT-363 PCB Layout
The INA-52063 is packaged in the
miniatureSOT-363(SC-70)
surface mount package. A PCB
pad layout for the SOT-363
package is shown in Figure 10
(dimensions are in inches). This
layout provides ample allowance
for package placement by
could impair the high frequency
performance of the INA-52063.
The layout is shown with a
nominal SOT-363 package
footprint superimposed on the
PCB pads for reference.
The INA-52063 is a silicon RFIC
amplifier that is designed with an
internal resistive feedback net-
work to provide a 50 Ω input and
50 Ω output impedance. With a
Third Order Intercept Point of
+20 dBm and a low Noise Figure
of 4 dB, the INA-52063 is
0.026
automated assembly equipment
without adding pad parasitics that
especially useful for RF and IF
amplifier applications requiring
high dynamic ranges.
0.07
REFERENCE
PLANES
0.035
Phase Reference Planes
The positions of the reference
planes used to measure
TEST CIRCUIT
0.016
S-Parameters for this device are
shown in Figure 9. As seen in the
illustration, the reference planes
are located at the point where the
package leads contact the test
circuit.
Figure 9. Phase Reference Planes.
Figure 10. PCB Pad Layout
(dimensions in inches).
6-159
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
