A
DVANCED
L
INEAR
D
EVICES,
I
NC.
ALD2724E/ALD2724
DUAL EPAD® PRECISION HIGH SLEW RATE CMOS OPERATIONAL AMPLIFIER
KEY FEATURES
•
•
•
•
•
•
Factory pre-trimmed V
OS
V
OS =
25
µ
V @ I
OS =
0.01pA
5 V /
µ
s slew rate
EPAD ( Electrically Programmable Analog Device)
Rail-to-rail input/output
Each amplifier V
OS
can be user trimmed to
a different Vos level (optional)
• System level “calibration” capable
BENEFITS
• Ready to use off the shelf standard part
• Custom automated trimming optional
• Remote controlled automated trimming
• In-System Programming capable
• No external components
• No internal clocking noise source
• Simple and cost effective
• Small package size
• Extremely small total functional
volume size
• Low system implementation cost
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Sensor interface circuits
Transducer biasing circuits
Capacitive and charge integration circuits
Biochemical probe interface
Signal conditioning
Portable instruments
High source impedance electrode
amplifiers
Precision Sample and Hold amplifiers
Precision current to voltage converter
Error correction circuits
Sensor compensation circuits
Precision gain amplifiers
Periodic In-system calibration
System output level shifter
GENERAL DESCRIPTION
The ALD2724E/ALD2724 is a dual monolithic operational amplifier with
MOSFET input that has rail-to-rail input and output voltage ranges. The
input voltage range and output voltage range are very close to the positive
and negative power supply voltages. Typically the input voltage can be
beyond positive power supply voltage V+ or the negative power supply
voltage V- by up to 300mV. The output voltage swings to within 60mV of
either positive or negative power supply voltages at rated load.
With high impedance load, the output voltage of the ALD2724E/ALD2724
approaches within 1mV of the power supply rails. This device is designed
as an alternative to the popular J-FET input operational amplifier in
applications where lower operating voltages, such as 9V battery or
±3.25V
to
±5V
power supplies are being used. The ALD2724E/ALD2724 offers
high slew rate of 5.0V/µs.
The rail-to-rail input and output feature of the ALD2724E/ALD2724 ex-
pands signal voltage range for a given operating supply voltage and allows
numerous analog serial stages to be implemented without losing operat-
ing voltage margin. The output stage is designed to drive up to 10mA into
400pF capacitive and 1.5KΩ resistive loads at unity gain and up to 4000pF
at a gain of 5. Short circuit protection to either ground or the power supply
rails is at approximately 15mA clamp current. Due to complementary
output stage design, the output can source and sink 10mA into a load with
symmetrical drive and is ideally suited for applications where push-pull
voltage drive is desired.
For each of the operational amplifier, the offset voltage is trimmed on-chip
to eliminate the need for external nulling in many applications. For
precision applications, the output is designed to settle to 0.1% in 2µs. In
large signal buffer applications, the operational amplifier can function as
PIN CONFIGURATION
-IN
A
+IN
A
N/C
1
2
3
4
14
13
12
11
10
9
8
TOP VIEW
DB, PB, SB PACKAGE
VE
2A
VE
1A
OUT
A
V+
OUT
B
VE
1B
VE
2B
ORDERING INFORMATION
Operating Temperature Range
-55°C to +125°C
14-Pin
CERDIP
Package
ALD2724E DB
ALD2724 DB
0°C to +70°C
14-Pin
Small Outline
Package (SOIC)
ALD2724E SB
ALD2724 SB
0°C to +70°C
14-Pin
Plastic Dip
Package
ALD2724E PB
ALD2724 PB
V-
N/C 5
+IN
B
-IN
B
6
7
* Contact factory for industrial temperature range
©2002 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, California 94089 -1706 Tel: (408) 747-1155 Fax: (408) 747-1286 http://www.aldinc.com
ALD [ ADVANCED LINEAR DEVICES ]
