AO4286
Electrical Characteristics (TJ=25°C unless otherwise noted)
Symbol Parameter
Conditions
Min
Typ
Max Units
STATIC PARAMETERS
ID=250µA, VGS=0V
BVDSS
Drain-Source Breakdown Voltage
100
V
VDS=100V, VGS=0V
1
IDSS
Zero Gate Voltage Drain Current
µA
5
TJ=55°C
VDS=0V, VGS=±20V
VDS=VGS,ID=250µA
VGS=10V, VDS=5V
VGS=10V, ID=4A
IGSS
Gate-Body leakage current
Gate Threshold Voltage
On state drain current
±100
2.9
nA
V
VGS(th)
ID(ON)
1.7
25
2.25
A
55.5
104
72.5
13
68
127
92
mΩ
RDS(ON)
Static Drain-Source On-Resistance
TJ=125°C
VGS=4.5V, ID=3A
mΩ
S
VDS=5V, ID=4A
gFS
VSD
IS
Forward Transconductance
Diode Forward Voltage
IS=1A,VGS=0V
0.76
1
3
V
Maximum Body-Diode Continuous Current
A
DYNAMIC PARAMETERS
Ciss
Coss
Crss
Rg
Input Capacitance
390
30
3
pF
pF
pF
Ω
VGS=0V, VDS=50V, f=1MHz
Output Capacitance
Reverse Transfer Capacitance
Gate resistance
VGS=0V, VDS=0V, f=1MHz
7
SWITCHING PARAMETERS
Qg(10V) Total Gate Charge
5.8
2.8
1.1
1.2
6
10
5
nC
nC
nC
nC
ns
Qg(4.5V) Total Gate Charge
VGS=10V, VDS=50V, ID=4A
Qgs
Qgd
tD(on)
tr
Gate Source Charge
Gate Drain Charge
Turn-On DelayTime
Turn-On Rise Time
Turn-Off DelayTime
Turn-Off Fall Time
VGS=10V, VDS=50V, RL=12.5Ω,
RGEN=3Ω
2.5
18
ns
tD(off)
tf
ns
2.5
ns
trr
IF=4A, dI/dt=500A/µs
IF=4A, dI/dt=500A/µs
Body Diode Reverse Recovery Time
Body Diode Reverse Recovery Charge
15
53
ns
Qrr
nC
A. The value of RθJA is measured with the device mounted on 1in2 FR-4 board with 2oz. Copper, in a still air environment with TA =25°C. The
value in any given application depends on the user's specific board design.
B. The power dissipation PD is based on TJ(MAX)=150°C, using ≤ 10s junction-to-ambient thermal resistance.
C. Repetitive rating, pulse width limited by junction temperature TJ(MAX)=150°C. Ratings are based on low frequency and duty cycles to keep
initialTJ=25°C.
D. The RθJA is the sum of the thermal impedance from junction to lead RθJL and lead to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-ambient thermal impedance which is measured with the device mounted on 1in2 FR-4 board with
2oz. Copper, assuming a maximum junction temperature of TJ(MAX)=150°C. The SOA curve provides a single pulse rating.
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Rev 0: Nov. 2012
www.aosmd.com
Page 2 of 5