ABSOLUTE MAXIMUM RATINGS
(1)
V
DD
to GND ........................................................................... –0.3V to +6V
Digital Input Voltage to GND .................................. –0.3V to +V
DD
+ 0.3V
V
OUT
to GND ........................................................... –0.3V to +V
DD
+ 0.3V
Operating Temperature Range ..................................... –40°C to +105°C
Storage Temperature Range ......................................... –65°C to +150°C
Junction Temperature Range (T
J
max) ......................................... +150°C
SOT23 Package:
Power Dissipation .................................................. (T
J
max — T
A
)/
JA
JA
Thermal Impedance ......................................................... 240°C/W
Lead Temperature, Soldering:
Vapor Phase (60s) ............................................................... +215°C
Infrared (15s) ........................................................................ +220°C
MSOP Package:
Power Dissipation ........................................................ (T
J
max — T
A
)/
JA
JA
Thermal Impedance ......................................................... 206°C/W
JC
Thermal Impedance ........................................................... 44°C/W
Lead Temperature, Soldering:
Vapor Phase (60s) ............................................................... +215°C
Infrared (15s) ........................................................................ +220°C
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
MINIMUM
RELATIVE
ACCURACY
(LSB)
±8
DIFFERENTIAL
NONLINEARITY
(LSB)
±1
SPECIFIED
TEMPERATURE
RANGE
–40°C to +105°C
PRODUCT
DAC7512E
PACKAGE-LEAD
MSOP-8
PACKAGE
DESIGNATOR
(1)
DGK
PACKAGE
MARKING
D12E
ORDERING
NUMBER
(1)
DAC7512E/250
DAC7512E/2K5
DAC7512N/250
DAC7512N/3K
TRANSPORT
MEDIA, QUANTITY
Tape and Reel, 250
Tape and Reel, 2500
Tape and Reel, 250
Tape and Reel, 3000
"
DAC7512N
"
±8
"
±1
"
SOT23-6
"
DBV
"
–40°C to +105°C
"
D12N
"
"
"
"
"
"
"
NOTES: (1) For the most current specifications and package information, refer to our web site at www.ti.com. (2) Models with a slash (/) are available only in Tape
and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “DAC7512E/2K5” will get a single 2500-piece Tape and Reel.
PIN CONFIGURATIONS
Top View
V
OUT
GND
V
DD
1
2
3
DAC7512
SOT23-6
6
5
4
SYNC
SCLK
D
IN
PIN DESCRIPTION (SOT23-6)
PIN
1
2
3
4
NAME
V
OUT
GND
V
DD
D
IN
DESCRIPTION
Analog output voltage from DAC. The output ampli-
fier has rail-to-rail operation.
Ground reference point for all circuitry on the part.
Power Supply Input, +2.7V to 5.5V.
Serial Data Input. Data is clocked into the 16-bit
input shift register on the falling edge of the serial
clock input.
Serial Clock Input. Data can be transferred at rates
up to 30MHz.
Level triggered control input (active LOW). This is
the frame sychronization signal for the input data.
When SYNC goes LOW, it enables the input shift
register and data is transferred in on the falling
edges of the following clocks. The DAC is updated
following the 16th clock cycle unless SYNC is taken
HIGH before this edge, in which case the rising
edge of SYNC acts as an interrupt and the write
sequence is ignored by the DAC7512.
MSOP-8
V
DD
NC
NC
V
OUT
1
2
DAC7512
3
4
6
5
8
7
GND
D
IN
SCLK
SYNC
5
6
SCLK
SYNC
NC = No Internal Connection
DAC7512N LOT TRACE LOCATION
Top View
Pin 1
Bottom View
D12N
Pin 1
YMLL
Lot Trace Code
2
DAC7512
www.ti.com
SBAS156B
BURR-BROWN [ BURR-BROWN CORPORATION ]
