CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
@Super
low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
@Rated
voltage range : 2.5 to 25V
dc
, case size range :
F6.3B5.2L
to
F10B12.2L
(Case code HC0 and JC0 newly added)
@Suitable
for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
@High
heat resistance to reflow soldering (See reflow soldering conditions)
@Pb-free
design
?SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105C
2.5 to 25V
dc
P20%
(M)
Rated voltageB1.15V
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
Characteristics
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Bias Humidity
Surge Voltage
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 105C.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[150%
of the initial specified value
ESR
[150%
of the initial specified value
Leakage current
[The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[150%
of the initial specified value
ESR
[150%
of the initial specified value
Leakage current
[The
initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[150%
of the initial specified value
ESR
[150%
of the initial specified value
Leakage current
[The
initial specified value
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS
[mm]
@Terminal
Code : A
W
FDP0.5
P
CP0.2
BP0.2
Size code
F55
F60
H70
J80
HC0
JC0
fD
6.3
6.3
8
10
8
10
L
A
B
C
5.2 6.6 6.6 7.2
5.7 6.6 6.6 7.2
6.7 8.3 8.3 9.0
7.7 10.3 10.3 11.0
12.0 8.3 8.3 9.0
12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.9
1.9
3.1
4.5
3.1
4.5
?MARKING
EX) PXA16VC39M
A
905
39
16
V
0.3max.
AP0.2
LP0.3 (Note)
Note : LP0.5 for HC0 and JC0
?PART
NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PXA
AAA
A RA
AAA
M
AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10MF:100,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
(1/2)
CAT. No. E1001E
CHEMI-CON [ UNITED CHEMI-CON, INC. ]
