OUTLINE DIMENSIONS & PIN CONNECTIONS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
∅1.00±0.20
[0.039±0.008]
H_RN
-
2W Series
H_LT-2W Series
H_RN-2W Series
23.86±0.20
[0.939±0.008]
23.86[0.939]
17.78[0.700]
16
1
10
17.78[0.700]
9
8
16
10
9
16
10
9
(Top View)
(Top View)
7
8
1
7
7
8
1
2.54[0.100]
0.50±0.10
[0.020±0.004]
2.54[0.100]
17.78[0.700]
2.54[0.100]
H_LT-2W Series
17.78±0.35
[0.700±0.700]
(Front View)
16
10
9
0.50[0.020]
1.02[0.040]
(Front View)
7
8
1
17.78±0.35
[0.700±0.014]
0.10[0.004]
MAX3.34[0.135]
MAX3.34[0.131]
15.53[0.611]
1.20±0.20
[0.047±0.008]
17.78[0.700]
Note: grid 2.54*2.54mm.
A
0.91±0.20
[0.045±0.008]
(Side View)
0~5
A
TUBE OUTLINE DIMENSIONS
(Side View)
1.34
[0.053]
2.20±0.20
[0.087±0.008]
22.60[0.890]
18.10±0.40
[0.713±0.016]
MAX18.00[0.709]
FOOTPRINT DETAILS
FOOTPRINT DETAILS
Function
Pin
Function
GND
NC
Pin
1
7
1
7
GND
NC
8.40[0.331]
8
NC
NC
8
Note:
9
10
16
+Vo
0V
Vin
+Vo
0V
Vin
Unit:mm[inch]
9
10
16
General tolerances:±0.50mm[±0.020inch]
L=530mm[20.866inch] Tube Quantity:21pcs
L=220mm[8.661inch] Tube Quantity: 8pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm;
Short tube outer packaging dimensions(with six inner packaging boxes):
L*W*H=375*280*270mm;
Long tube inner packaging dimensions: L*W*H=580*200*100mm;
Long tube outer packaging dimensions(with two inner packaging boxes)：
L*W*H=600*215*220mm;
NC:No connection
Note:
Unit:mm[inch]
Pin section tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
Long tube outer packaging dimensions(with three inner packaging boxes)：
L*W*H=600*215*325mm.
TAPING REEL DIMENSIONS
18.42[0.725]
1.50[0.059]
2.00[0.079]
14.00[0.551]
4.00[0.157]
0.50[0.020]
44.80[1.764]
100.00[3.937]
1.70[0.067]
13.00[0.512]
21.50[0.846]
9.70[0.382]
1.50[0.059]
Note:
28.00[1.102]
2.00[0.079]
Per reel of packing quantity:200PCS
Innerpackage cartondimensions:L*W*H=365*350*105mm
Tube Quantity:400pcs
Unit:mm [inch]
General Tolerances:±0.50mm [± 0.020inch]
Outerpackagecartondimensions:L*W*H=390*360*245mm
Tube Quantity:800pcs
Note:
1.Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life of
product.
2.All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3.Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
H_RN-2W & H_LT-2W C/0-2012 Page 3 of 3
CRYSTEKMICROWAVE [ CRYSTEK CORPORATION ]
