DATA SHEET
256M bits DDR SDRAM
EDD2504AKTA-E (64M words
×
4 bits)
Description
The EDD2504AKTA is a 256M bits Double Data Rate
(DDR) SDRAM organized as 16,777,216 words
×
4 bits
×
4 banks. Read and write operations are performed at
the cross points of the CK and the /CK. This high-
speed data transfer is realized by the 2 bits prefetch-
pipelined architecture. Data strobe (DQS) both for
read and write are available for high speed and reliable
data bus design. By setting extended mode register,
the on-chip Delay Locked Loop (DLL) can be set
enable or disable. It is packaged in 66-pin plastic
TSOP (II).
Pin Configurations
/xxx indicates active low signal.
66-pin Plastic TSOP(II)
VDD
NC
VDDQ
NC
DQ0
VSSQ
NC
NC
VDDQ
NC
DQ1
VSSQ
NC
NC
VDDQ
NC
NC
VDD
NC
NC
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10(AP)
A0
A1
A2
A3
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
(Top view)
Features
•
Power supply : VDDQ = 2.5V
±
0.2V
: VDD = 2.5V
±
0.2V
•
Data rate: 333Mbps/266Mbps (max.)
•
Double Data Rate architecture; two data transfers per
clock cycle
•
Bi-directional, data strobe (DQS) is transmitted
/received with data, to be used in capturing data at
the receiver
•
Data inputs, outputs, and DM are synchronized with
DQS
•
4 internal banks for concurrent operation
•
DQS is edge aligned with data for READs; center
aligned with data for WRITEs
•
Differential clock inputs (CK and /CK)
•
DLL aligns DQ and DQS transitions with CK
transitions
•
Commands entered on each positive CK edge; data
and data mask referenced to both edges of DQS
•
Data mask (DM) for write data
•
Auto precharge option for each burst access
•
SSTL_2 compatible I/O
•
Programmable burst length (BL): 2, 4, 8
•
Programmable /CAS latency (CL): 2, 2.5
•
Programmable output driver strength: normal/weak
•
Refresh cycles: 8192 refresh cycles/64ms
7.8µs maximum average periodic refresh interval
•
2 variations of refresh
Auto refresh
Self refresh
•
TSOP (II) package with lead free solder (Sn-Bi)
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
VSS
NC
VSSQ
NC
DQ3
VDDQ
NC
NC
VSSQ
NC
DQ2
VDDQ
NC
NC
VSSQ
DQS
NC
VREF
VSS
DM
/CK
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
A0 to A12
BA0, BA1
DQ0 to DQ3
DQS
/CS
/RAS
/CAS
/WE
DM
CK
/CK
CKE
VREF
VDD
VSS
VDDQ
VSSQ
NC
Address input
Bank select address
Data-input/output
Input and output data strobe
Chip select
Row address strobe command
Column address strobe command
Write enable
Input mask
Clock input
Differential clock input
Clock enable
Input reference voltage
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
Document No. E0610E10 (Ver. 1.0)
Date Published November 2004 (K) Japan
URL: http://www.elpida.com
Elpida
Memory, Inc. 2004
ELPIDA [ ELPIDA MEMORY ]
