EN25QH16
Table 3. Protected Area Sizes Sector Organization
Status Register Content
BP3
Bit
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
BP2
Bit
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
BP1
Bit
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
BP0
Bit
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Protect Areas
None
Block 31
Block 30 to 31
Block 28 to 31
Block 24 to 31
Block 16 to 31
All
All
None
Block 0
Block 0 to 1
Block 0 to 3
Block 0 to 7
Block 0 to 15
All
All
Memory Content
Addresses
None
1F0000h-1FFFFFh
1E0000h-1FFFFFh
1C0000h-1FFFFFh
180000h-1FFFFFh
100000h-1FFFFFh
000000h-1FFFFFh
000000h-1FFFFFh
None
000000h-00FFFFh
000000h-01FFFFh
000000h-03FFFFh
000000h-07FFFFh
000000h-0FFFFFh
000000h-1FFFFFh
000000h-1FFFFFh
Density(KB)
None
64KB
128KB
256KB
512KB
1024KB
2048KB
2048KB
None
64KB
128KB
256KB
512KB
1024KB
2048KB
2048KB
Portion
None
Upper 1/32
Upper 2/32
Upper 4/32
Upper 8/32
Upper 16/32
All
All
None
Lower 1/32
Lower 2/32
Lower 4/32
Lower 8/32
Lower 16/32
All
All
INSTRUCTIONS
All instructions, addresses and data are shifted in and out of the device, most significant bit first. Serial
Data Input (DI) is sampled on the first rising edge of Serial Clock (CLK) after Chip Select (CS#) is
driven Low. Then, the one-byte instruction code must be shifted in to the device, most significant bit first,
on Serial Data Input (DI), each bit being latched on the rising edges of Serial Clock (CLK).
The instruction set is listed in Table 4. Every instruction sequence starts with a one-byte instruction
code. Depending on the instruction, this might be followed by address bytes, or by data bytes, or by
both or none. Chip Select (CS#) must be driven High after the last bit of the instruction sequence has
been shifted in. In the case of a Read Data Bytes (READ), Read Data Bytes at Higher Speed
(Fast_Read), Dual Output Fast Read (3Bh), Dual I/O Fast Read (BBh), Quad Input/Output
FAST_READ (EBh), Read Status Register (RDSR), Read Information Register (RDIFR) or Release
from Deep Power-down, and Read Device ID (RDI) instruction, the shifted-in instruction sequence is
followed by a data-out sequence. Chip Select (CS#) can be driven High after any bit of the data-out
sequence is being shifted out.
In the case of a Page Program (PP), Sector Erase (SE), Block Erase (BE), Chip Erase (CE), Write
Status Register (WRSR), Write Enable (WREN), Write Disable (WRDI) or Deep Power-down (DP)
instruction, Chip Select (CS#) must be driven High exactly at a byte boundary, otherwise the instruction
is rejected, and is not executed. That is, Chip Select (CS#) must driven High when the number of clock
pulses after Chip Select (CS#) being driven Low is an exact multiple of eight. For Page Program, if at
any time the input byte is not a full byte, nothing will happen and WEL will not be reset.
In the case of multi-byte commands of Page Program (PP), and Release from Deep Power Down
(RES ) minimum number of bytes specified has to be given, without which, the command will be
ignored.
In the case of Page Program, if the number of byte after the command is less than 4 (at least 1
data byte), it will be ignored too. In the case of SE and BE, exact 24-bit address is a must, any
less or more will cause the command to be ignored.
All attempts to access the memory array during a Write Status Register cycle, Program cycle or Erase
cycle are ignored, and the internal Write Status Register cycle, Program cycle or Erase cycle continues
unaffected.
This Data Sheet may be revised by subsequent versions
©2004 Eon Silicon Solution, Inc.,
11
or modifications due to changes in technical specifications.
Rev. H, Issue Date: 2012/01/30
www.eonssi.com
EON [ EON SILICON SOLUTION INC. ]
