S1C17801
CMOS 16-bit Application Specific Controller
●
16-bit RISC CPU Core S1C17 (Max. 48 MHz operation)
●
128K-Byte Flash ROM and 4K + 2K-Byte RAM
(2K-byte RAM is operable with separated power supply)
●
Multiply and Accumulation Function (16 bits
×
16 bits + 32 bits MAC)
●
Built-in USB FS-Device Controller
●
10-bit ADC
●
I
2
S Interface
●
IGBT Control Function by PWM Timer
●
Infrared Remote Control Signal Transceiver and Receiver Circuit
●
Built-in STN LCD Controller with 2K-Byte VRAM
Display 120
×
120 pixels in 1 bpp Mode using IVRAM
Support QVGA (320
×
240) in 4 bpp Mode using External VRAM
●
NAND Flash Card Interface
■
DESCRIPTIONS
The S1C17801 is a high performance and compact 16-bit RISC application specific controller (ASC). It is suitable for
various products that require analog inputs, display and interfaces for connection, such as healthcare goods, sensor
systems, alarms, home electric appliance (rice cookers, microwave ovens and remote controllers).
The S1C17801 consists of a S1C17 16-bit compact RISC CPU Core, a 128K-byte Flash EEPROM, a 4K + 2K-byte RAM,
a 10-bit ADC with eight analog input channels, a USB FS-device controller, a PWM control capture timer/counter, an
infrared remote controller, serial interfaces (UART with IrDA 1.0, SPI, I
2
C, and I
2
S), an RTC driven with an independent
power supply, 16-bit and 8-bit timers, a watchdog timer, a NAND Flash card interface, an external bus with an SRAM
controller, GPIO ports and an STN LCD controller with built-in VRAM.
The LCD controller supports an external VRAM to display using a large size STN LCD panel. It also supports an LCD
driver DMA function to interface with an EPSON S1D15xxx built-in RAM LCD driver and a driver with an SPI.
The USB FS-device controller may be used not only for communication with PCs but also for on-board firmware update.
The S1C17801 provides a 16 bits
×
16 bits + 32 bits MAC (multiply and accumulate) instruction to implement a DSP
function. Furthermore, an external audio ADC/DAC may be connected via the built-in I
2
S interface, this makes it possible
to input/output ADPCM sound/voice data.
The S1C17801 has adopted the EPSON SoC (System on Chip) design technology using 0.35 μm mixed analog low power
CMOS process.
Product Lineup
Model No.
Flash ROM size
RAM size
Package
S1C17801F
128K bytes
4K + 2K* bytes TQFP15-128pin
S1C17801B
96K bytes
4K + 2K* bytes
PFBGA7U-144
∗
The 2K-byte RAM with battery backup (separated power used) is configurable as VRAM.
This product uses SuperFlash
®
Technology licensed from Silicon Storage Technology, Inc.
■
FEATURES
●
Technology
●
CPU
• Seiko Epson original 16-bit RISC processor S1C17 Core
• Internal 3-stage pipeline
• Instruction set
- 16-bit fixed length
- 111 basic instructions (184 including variations)
- Compact and fast instruction set optimized for development in C language
• Registers
- Eight 24-bit general-purpose registers
- Three special registers (24-bit
×
2, 8-bit
×
1)
• Memory space
- Up to 16M bytes accessible (24-bit address)
• 0.35 μm AL-4-layers mixed analog low power CMOS process technology
SEIKO EPSON CORPORATION
EPSON [ EPSON COMPANY ]
