100352
Absolute Maximum Ratings
(Note 1)
Storage Temperature (T
STG
)
Maximum Junction Temperature (T
J
)
V
EE
Pin Potential to Ground Pin
Input Voltage (DC)
Output Current (DC Output HIGH)
ESD (Note 2)
−
65
°
C to
+
150
°
C
+
150
°
C
−
7.0V to
+
0.5V
V
EE
to
+
0.5V
Recommended Operating
Conditions
Case Temperature (T
C
)
Commercial
Industrial
Supply Voltage (V
EE
)
0
°
C to
+
85
°
C
−
40
°
C to
+
85
°
C
−
5.7V to
−
4.2V
−
100 mA
≥
2000V
Note 1:
The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 2:
ESD testing conforms to MIL-STD-883, Method 3015.
Commercial Version
DC Electrical Characteristics
(Note 3)
V
EE
= −
4.2V to
−
5.7V, V
CC
=
V
CCA
=
GND, T
C
=
0°C to
+85°C
Symbol
Parameter
Min
Typ
V
OH
V
OL
V
OHC
V
OLC
V
OLZ
V
IH
V
IL
I
IL
I
IH
I
EE
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Cut-Off LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input LOW Current
Input HIGH Current
Power Supply Current
−138
−143
−70
−70
mA
−1165
−1830
0.50
240
−1025
−1830
−1035
−1610
−1950
−870
−1475
−955
−1705
Max
−870
−1620
Units
mV
mV
mV
mV
mV
µA
µA
V
IN
=V
IH (Max)
or V
IL (Min)
V
IN
=
V
IH (Min)
or V
IL (Max)
V
IN
=
V
IH (Min)
or V
IL (Max)
Guaranteed HIGH Signal
for All Inputs
Guaranteed LOW Signal
for All Inputs
V
IN
=
V
IL (Min)
V
IN
=
V
IH (Max)
Inputs Open
V
EE
= −4.2V
to
−4.8V
V
EE
= −4.2V
to
−5.7V
Conditions
Loading with
25Ω to
−2.0V
Loading with
25Ω to
−2.0V
OEN
=
HIGH
Note 3:
The specified limits represent the “worst case” value for the parameter. Since these values normally occur at the temperature extremes, additional
noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are cho-
sen to guarantee operation under “worst case” conditions.
DIP AC Electrical Characteristics
V
EE
= −
4.2V to
−
5.7V, V
CC
=
V
CCA
=
GND
Symbol
t
PLH
t
PHL
t
PZH
t
PHZ
t
TLH
t
THL
Parameter
Propagation Delay
Dn to Output
Propagation Delay
OEN to Output
Transition Time
20% to 80%, 80% to 20%
T
C
=
0°C
Min
0.70
1.60
1.00
0.45
Max
2.00
4.20
2.70
2.00
T
C
= +25°C
Min
0.70
1.60
1.00
0.45
Max
2.00
4.20
2.70
2.00
T
C
= +85°C
Min
0.70
1.60
1.00
0.45
Max
2.20
4.20
2.70
2.00
Units
ns
ns
ns
Conditions
Figures 1, 2
(Note 4)
Figures 1, 2
(Note 4)
Figures 1, 2
Note 4:
The propagation delay specified is for single output switching. Delays may vary up to 300 ps with multiple outputs switching.
3
www.fairchildsemi.com