PIN-1310-10LR-SC
10 GBPS 1310NM PIN + PREAMP
ELECTRO-OPTICAL CHARACTERISTICS
3.0V<Vcc<3.6V, AC coupled to 50Ω (100Ωdifferential), -10°C<T<85°C unless otherwise specified, with flex circuit
VCSEL Parameters
Data Rate
Supply Voltage
Supply Current
Optical Return Loss
Input Optical Wavelength
PD Responsivity
PD Bias
Maximum Average Input Power
before Overload
Differential Output Voltage
Swing
Differential Responsivity
-3dB Optical/Electrical
Bandwidth
Low Frequency –3dB Cutoff
Output Impedance
Output Return Loss
Sensitivity
Stressed Sensitivity
Rise/Fall Time
Differential Power Supply
Rejection Ratio
Group Delay
P
R,OMA
= -12Bm,
AC Coupled to R
L
=50Ω
P
R,OMA
= -12dBm,
AC Coupled to R
L
=50Ω
T
A
= 25°C
P
R
=0μW, R
L
=50ΩAC
coupled
P
R
=-12dBm
λ = 1310nm
I
CC
ORL
λ
P
Resp
V
PD
P
MAX
V
o(pk-pk)
T
BW
BW
LF
Z
OUT
S
22
S
S
STRESS
T
R
/T
F
PSRR
Delay
12
1260
0.8
3.0
+1
100
3000
7.5
30
60
-7
-16.5
-12
45
Test Condition
Symbol
DR
Min.
0.1
3.0
Typ.
3.3
35
Max.
11.3
3.6
60
Units
Gbps
V
mA
1
1620
0.85
3.3
+3
600
3.6
dBm
mV
V/W
1,2
GHz
KHz
Ω
dB
dBm
dBm
ps
dB
50
ps
1,2,3
1,2,3
1,2
dB
nm
A/W
1
1
Notes
40
50
R
0
=50Ω, DC 10≤GHZ
DR = 10.3125Gbps
Circadiant Test
P
R,OMA
=-12dBm, (20%-
80%),
P
R
=0μW (Dark),
5MHz<F<2GHz
P
R,OMA
= -12dBm,
AC Coupled to R
L
=50Ω
2MHz<F<6GHz
4
4
2,5
1,6
7
20
-50
NOTES:
1.
2.
P
R
is the average optical power at the fiber face.
P
R,OMA
is the peak to peak optical power at the fiber face (Optical Modulation Amplitude)
P
R
,
OMA
≡
3.
4.
2
P
R
(
ER
−
1
)
ER
+
1
where ER is the extinction ratio (linear) of the optical source.
Bandwidth and Low Frequency Cutoff are measured with a small signal sinusoidal light source with –10dBm average power
Sensitivity is measured with an optical source with an extinction ratio of 6dB. For sensitivity measurements at 10.3125, 10.51875, 10.70923, 11.09573,
11.31764 Gb/s, PRBS 2^31-1, ER=6dB, BER < 10
-12
and with limiting of the TIA is assumed to be implemented at the front end of the post amplifier. Stress
testing is done using a Circadiant test system
Rise/Fall times are corrected for optical source Rise/Fall times.
2
2
2
T
TIA
=
T
MEASURED
−
T
OPTICAL
5.
6.
7.
8.
9.
10.
Value shown is with no external power supply filtering.
Group delay is a sensitive measurement to package interface, and includes the effects of PD, TIA and package. Measurement is made with TO leads as short
as possible.
DJ
TIA
is specified as contributed DJ by the TIA, obtained from
RJ
TIA
is specified as contributed RJby the TIA, obtained from
2
2
2
DJ
TIA
=
DJ
TOTAL
−
DJ
OPTICAL
2
2
2
RJ
TIA
=
RJ
TOTAL
−
RJ
OPTICAL
The electrical performance of the ROSA is dependent upon the quality of the electrical connection between the TO can and the circuit board. AOC cannot
guarantee all performance specifications for parts without the flex circuit attached.
FINISAR [ FINISAR CORPORATION. ]
