欢迎访问ic37.com |
会员登录 免费注册
发布采购

MC12095 参数 Datasheet PDF下载

MC12095图片预览
型号: MC12095
PDF下载: 下载PDF文件 查看货源
内容描述: 2.5 GHz的低功耗分频器采用待机模式 [2.5 GHz Low Power Prescaler With Stand-By Mode]
分类和应用:
文件页数/大小: 5 页 / 246 K
品牌: FREESCALE [ FREESCALE SEMICONDUCTOR, INC ]
 浏览型号MC12095的Datasheet PDF文件第2页浏览型号MC12095的Datasheet PDF文件第3页浏览型号MC12095的Datasheet PDF文件第4页浏览型号MC12095的Datasheet PDF文件第5页  
Freescale Semiconductor, Inc.
Order this document by MC12095/D
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
2.5 GHz Low Power Prescaler
With Stand-By Mode
MC12095
ARCHIVE INFORMATION
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
8
2.5 GHz Toggle Frequency
Supply Voltage 2.7 V to 5.5 Vdc
Low Power 8.7 mA Typical
Operating Temperature –40 to 85°C
Divide by 2 or 4 Selected by the SW Pin
1
NOTE:
For applications up to 1.1 GHz, please consult the MC12093
datasheet.
MOSAIC V is a trademark of Motorola
FUNCTIONAL TABLE
SW
H
L
Divide Ratio
2
4
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
PIN CONNECTIONS
NOTES:
1. SW: H = (VCC – 0.4 V) to VCC; L = OPEN
2. SB: H = 2.0 V to VCC; L = GND to 0.8 V
IN
VCC
NC
OUT
1
2
3
4
8
7
6
5
IN
SB
SW
Gnd
(Top View)
AC Test Circuit
ORDERING INFORMATION
VCC = 2.7 to 5.5 V
C3
C1
IN
50
C2
VCC
SB
SW
IN
GND
C4
OUT
EXTERNAL
COMPONENTS
C1 = C2 = 1000 pF
C3 = 0.1
µF
C4 = 2.0 pF
Device
MC12095D
Operating
Temp Range
TA = –40 to 85°C
Package
SO–8
©
Motorola, Inc. 1998
Rev 4
MOTOROLA RF/IF DEVICE DATA
For More Information On This Product,
1
Go to: www.freescale.com
ARCHIVE INFORMATION
Freescale Semiconductor, Inc...
The MC12095 is a single modulus prescaler for low power frequency
division of a 2.5 GHz high frequency input signal. Motorola’s advanced
MOSAIC™ V technology is utilized to acheive low power dissipation of
24 mW at a minimum supply voltage of 2.7 V.
On–chip output termination provides output current to drive a 2.0 pF
(typical) high impedance load. If additional drive is required for the prescaler
output, an external resistor can be added in parallel from the OUT pin to
GND to increase the output power. Care must be taken not to exceed the
maximum allowable current through the output.
Divide ratio control input (SW) selects the required divide ratio of
÷2
or
÷4.
Stand–By mode is available to reduce current drain to 100µA typical when
the standby pin SB is switched LOW disabling the prescaler.
MECL PLL COMPONENTS
÷2, ÷4
LOW POWER
PRESCALER
WITH STAND–BY MODE
SEMICONDUCTOR
TECHNICAL DATA