AM26LS32
MAXIMUM RATINGS
Rating
Power Supply Voltage
Input Common Mode Voltage
Input Differential Voltage
Three–State Control Input Voltage
Output Sink Current
Storage Temperature
Operating Junction Temperature
Symbol
VCC
VICM
VID
VI
IO
Tstg
TJ
Value
7.0
±
25
±
25
7.0
50
– 65 to + 150
+ 150
Unit
Vdc
Vdc
Vdc
Vdc
mA
°C
°C
RECOMMENDED OPERATING CONDITIONS
Rating
Power Supply Voltage
Operating Ambient Temperature
Input Common Mode Voltage Range
Input Differential Voltage Range
Symbol
VCC
TA
VICR
VIDR
Value
4.75 to 5.25
0 to + 70
– 7.0 to + 7.0
6.0
Unit
Vdc
°C
Vdc
Vdc
ELECTRICAL CHARACTERISTICS
(Unless otherwise noted, minimum and maximum limits apply over recommended temperature
and power supply voltage ranges. Typical values are for TA = 25°C, VCC = 5.0 V and VIC = 0 V. See Note 1.)
Characteristic
Input Voltage – High Logic State (Three–State Control)
Input Voltage – Low Logic State (Three–State Control)
Differential Input Threshold Voltage (Note 2)
(– 7.0 V
VIC
7.0 V, VIH = 2.0 V)
(IO = – 0.4 mA, VOH
2.7 V)
(IO = 8.0 mA, VOL
0.45 V)
Symbol
VIH
VIL
VTH(D)
–
–
–
–
0.2
– 0.2
mA
–
–
Rin
6.0 K
–
–
–
2.3
– 2.8
–
Ohms
V
VOH
VOL
IOZ
–
–
IOS
IIL
IIH
–
–
VIK
ICC
–
–
–
–
–
–
20
100
– 1.5
70
V
mA
– 15
–
–
–
–
–
– 20
20
– 85
– 360
mA
µA
µA
2.7
–
–
–
–
0.45
µA
Min
2.0
–
Typ
–
–
Max
–
0.8
Unit
V
V
V
p
p
q
p
Input Bias Current
(VCC = 0 V or 5.25) (Other Inputs at –15 V
Vin = + 15 V
Vin = – 15 V
Input Resistance ( –15 V
p
Vin
p
+ 15 V)
IIB(D)
p
Vin
p
+ 15 V)
Input Balance and Output Level
(– 7.0 V
VIC
7.0 V, VIH = 2.0 V, See Note 3)
(IO = – 0.4 mA, VID = 0.4 V)
(IO = 8.0 mA, VID = – 0.4 V)
p
p
Output Third State Leakage Current
(VI(D) = + 3.0 V, VIL = 0.8 V, VO = 0.4 V)
(VI(D) = – 3.0 V, VIL = 0.8 V, VO = 2.4 V)
Output Short Circuit Current
(VI(D) = 3.0 V, VIH = 2.0 V, VO = 0 V, See Note 4)
Input Current – Low Logic State (Three–State Control)
(VIL = 0.4 V)
Input Current – High Logic State (Three–State Control)
(VIH = 2.7 V)
(VIH = 5.5 V)
Input Clamp Diode Voltage (Three–State Control)
(IIC = – 18 mA)
Power Supply Current (VIL = 0 V) (All Inputs Grounded)
NOTES:
1. All currents into device pins are shown as positive, out of device pins are negative. All voltages referenced to ground unless otherwise noted.
2. Differential input threshold voltage and guaranteed output levels are done simultaneously for worst case.
3. Refer to EIA–422/3 for exact conditions. Input balance and guaranteed output levels are done simultaneously for worst case.
4. Only one output at a time should be shorted.
2
MOTOROLA ANALOG IC DEVICE DATA