欢迎访问ic37.com |
会员登录 免费注册
发布采购

GPDW3V320RPSRT002 参数 Datasheet PDF下载

GPDW3V320RPSRT002图片预览
型号: GPDW3V320RPSRT002
PDF下载: 下载PDF文件 查看货源
内容描述: DORADO 24V或48V输入, 1.5V , 1.8V , 2.0V , 2.5V , 3.3V DC , 20A输出或5.0V DC, 15A输出 [DORADO 24V or 48V Input, 1.5V, 1.8V, 2.0V, 2.5V, 3.3V DC, 20A Output or 5.0V DC, 15A Output]
分类和应用:
文件页数/大小: 6 页 / 755 K
品牌: GALAXY [ GALAXY POWER, INC. ]
 浏览型号GPDW3V320RPSRT002的Datasheet PDF文件第1页浏览型号GPDW3V320RPSRT002的Datasheet PDF文件第2页浏览型号GPDW3V320RPSRT002的Datasheet PDF文件第3页浏览型号GPDW3V320RPSRT002的Datasheet PDF文件第5页浏览型号GPDW3V320RPSRT002的Datasheet PDF文件第6页  
Application Notes  
Output Over Voltage Protection:  
Trim:  
The output voltage is constantly monitored by the  
microprocessor and a parallel regulation path with an  
independent reference. If the output voltage exceeds  
the over-voltage specification, the microprocessor will  
latch the converter off. To turn the converter on requires  
either cycling the ON/OFF pin or power to the  
converter. This advanced feature prevents the converter  
from damaging the load if there is a converter failure or  
application error. If non-latching is required, consult  
factory.  
To trim the output voltage higher, connect the  
required trim resistor from the Trim pin to the +Sense  
pin. To trim the output voltage lower, connect the  
required trim resistor from the Trim pin to the –Sense  
pin. See diagram below.  
Trim-down  
Thermal Shutdown:  
The printed circuit board temperature is measured  
using a semiconductor sensor. If the maximum rated  
temperature is exceeded, the converter is latched off. To  
re-enable the converter requires cycling the ON/OFF  
pin or power to the converter. If non-latching is  
required, consult factory.  
Trim-down (%)  
Control Options:  
100  
As the behavior of the circuit is determined by  
firmware in the microcontroller, specific customer  
requirements such as  
RTRIM-DOWN  
=
– 2  
5.11kΩ  
{% }  
Trim-up  
• non-latching thermal protection  
• custom valid input voltage range  
• controlled delay from initiating an ON/OFF  
signal for power sequencing  
can be accomplished with no change to hardware.  
The standard behavior was chosen based on system  
design experience but we understand that customers  
often have their own requirements.  
Please consult Galaxy Power for your special needs.  
Remote Sense:  
The output voltage is regulated at the point where the  
sense pins connect to the power output pins. Total sense  
compensation should not exceed 0.4V or 10% of Vout,  
whichever is greater.  
VO(100+%) (100+2%)  
RTRIM-UP  
=
5.11kΩ  
{
}
1.225%  
%  
Safety:  
An external input fuse must always be used to meet  
External Output Trimming  
these safety requirements.  
+ Sense  
Trim  
– Sense  
Dorado, Page 4  
Part No. 01-002 Rev. 1.0–110802  
PRODUCT PREVIEW