Specifications DG200
Absolute Maximum Ratings
V+, V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <36V
V+ - V
D
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
V
D
- V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
V
D
- V
S
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <28V
V
IN
- GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
Storage Temperature Range . . . . . . . . . . . . . . . . . -65
o
C to +150
o
C
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300
o
C
Thermal Information
Thermal Resistance
θ
JA
θ
JC
o
C/W
Ceramic DIP Package . . . . . . . . . . . . . . .
95
24
o
C/W
Plastic DIP Package . . . . . . . . . . . . . . . . 100
o
C/W
-
Metal Can Package . . . . . . . . . . . . . . . . . 136
o
C/W 65
o
C/W
Operating Temperature Range
“A” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to +125
o
C
“B” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25
o
C to +85
o
C
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to +70
o
C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications
(T
A
= +25
o
C, V+ = +15V, V- = -15V)
MILITARY
COMMERCIAL / INDUSTRIAL
+125
o
C
±10
±10
100
-
-
0
o
C TO
-25
o
C
-
-
80
-
-
+25
o
C
±10
±10
80
30 (Typ)
±15V
+70
o
C TO
+85
o
C
±10
±10
100
-
-
UNITS
µA
µA
Ω
Ω
V
PARAMETER
Input Logic Current,
I
IN(ON)
Input Logic Current,
I
N(OFF)
Drain-Source On Resis-
tance, r
DS(ON)
Channel-to-Channel
r
DS(ON)
Match, r
DS(ON)
Minimum Analog Signal
Handling Capability,
V
ANALOG
Switch OFF Leakage
Current, I
D(OFF)
Switch OFF Leakage
Current, I
S(OFF)
TEST CONDITIONS
V
IN
= 0.8V (Notes 2, 3)
V
IN
= 2.4V (Notes 2, 3)
I
S
= 10mA, V
ANALOG
=
±10V
-55
o
C
±
10
±10
70
-
-
+25
o
C
±1
±1
70
25 (Typ)
±15V
V
ANALOG
= -14V to +14V
V
ANALOG
= -14V to +14V
-
-
-
-
-
-
-
±2
±2
±2
1.0
0.5
15 (Typ)
54 (Typ)
100
100
200
-
-
-
-
-
-
-
-
-
-
-
±
5
±
5
±10
1.0
0.5
20 (Typ)
50 (Typ)
100
100
200
-
-
-
-
nA
nA
nA
µs
µs
mV
dB
Switch ON Leakage Cur- V
D
= V
S
= -14V to +14V
rent, I
D(ON)
+ I
S(ON)
Switch “ON” Time
(Note 1), t
ON
Switch “OFF” Time, t
OFF
Charge Injection, Q
(INJ.)
Minimum Off Isolation
Rejection Ratio, OIRR
+Power Supply
Quiescent Current, I
V1
-Power Supply
Quiescent Current, I
V2
Minimum Channel to
Channel Cross Coupling
Rejection Ratio, CCRR
NOTES:
1. Pull Down Resistor must be
≤
2kΩ
.
One Channel Off
R
L
= 1kΩ, V
ANALOG
=
-10V to +10V (Figure 5)
R
L
= 1kΩ, V
ANALOG
=
-10V to +10V (Figure 5)
Figure 6
f = 1MHz, R
L
= 100Ω,
C
L
≤
5pF
(Figure 7, Note 1)
V
IN
= 0V or V
IN
= 5V
1000
1000
-
1000
1000
54 (Typ)
2000
2000
-
1000
1000
-
1000
1000
50 (Typ)
2000
2000
-
µA
µA
dB
2. Typical values are for design aid only, not guaranteed and not subject to production testing.
3. All channels are turned off by high “1” logic inputs and all channels are turned on by low “0” inputs; however 0.8V to 2.4V describes the
minimum range for switching properly. Peak input current required for transition is typically -120µA.
9-15
HARRIS [ HARRIS CORPORATION ]
