s1mm
Pitch Type Bottom Contact Type
2.3
1.0
(0.2)
0.8
A
E
Mated Cross-sectional Diagram
1.2
2
FPC/FFC Contact Surface
(2.1)
(3.1)
(1.3)
B
C
(4.8)
D
2
1.85
4.6
5.6
Unit:mm
Part Number
FH12-05S-1SH
FH12-06S-1SH
Standard type
CL No.
586-0591-6
586-0607-4
586-0535-5
586-0579-0
586-0540-5
586-0668-9
586-0536-8
586-0547-4
586-0592-9
586-0537-0
586-0538-3
586-0539-6
586-0541-8
586-0542-0
586-0543-3
586-0546-1
586-0548-7
Number of Contacts
5
6
7
8
9
11
16
22
26
4
6
8
10
11
14
19
24
A
04
05
06
07
08
10
15
21
25
03
05
07
09
10
13
18
23
B
08.6
09.6
10.6
11.6
12.6
14.6
19.6
25.6
29.6
08.1
10.1
12.1
14.1
15.1
18.1
23.1
28.1
C
09.6
10.6
11.6
12.6
13.6
15.6
20.6
26.6
30.6
09.1
11.1
13.1
15.1
16.1
19.1
24.1
29.1
D
06.07
07.07
08.07
09.07
10.07
12.07
17.07
23.07
27.07
05.57
07.57
09.57
11.57
12.57
15.57
20.57
25.57
E
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
FH12-07S-1SH
FH12-08S-1SH
FH12-09S-1SH
FH12-11S-1SH
FH12-16S-1SH
FH12-22S-1SH
FH12-26S-1SH
FH12-10(4)SA-1SH
FH12-14(6)SA-1SH
Eccentric type
FH12-18(8)SA-1SH
FH12-22(10)SA-1SH
FH12-24(11)SA-1SH
FH12-30(14)SA-1SH
FH12-40(19)SA-1SH
FH12-50(24)SA-1SH
Note 1: Embossed tape reel packaging (2,000 pieces/reel).
Order by number of reels.
Note 2: The 1mm version of FH12 is constructed by loading every other contact into the 0.5mm housing.
When a housing designed for an odd number of 0.5mm pitch contacts is used; the spacing from the
edge to the first contact on either side is the same as the distance between each contact, 1.0mm.
Hirose considers this design to be a
standard-type 1.0mm
connector.
Note 2:
An
eccentric-type
connector using a housing designed for an even number of 0.5mm pitch contacts
and consequently one side has 1.5mm distance from the edge to the first contact. (See FPC/FFC
dimensional drawing on page 19) The part number for the eccentric type describes the size of the
0.5mm housing used and lists the number of 1.0mm pitch contacts in parentheses () as shown in the
above table.
18