X25057
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias
................... –65°C to +135°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to V
SS
................................... –1V to +7V
D.C. Output Current .............................................. 5mA
Lead Temperature
(Soldering, 10 seconds)
.............................. 300°C
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Supply Voltage
X25057
X25057-2.7
X25057-1.8
Limits
4.5V to 5.5V
2.7V to 5.5V
1.8V to 3.6V
7033 FRM T05
Min.
0°C
–40°C
Max.
+70°C
+85°C
7033 FRM T04
D.C. OPERATING CHARACTERISTICS
(Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
I
CC1
I
CC2
I
SB
I
LI
I
LO
Parameter
V
CC
Supply Current (Write)
V
CC
Supply Current (Read )
V
CC
Supply Current
(Standby)
Min.
Max.
3
400
1
10
10
Units
mA
∝A
∝A
∝A
∝A
V
V
V
V
V
V
V
V
Test Conditions
SCK = V
CC
x 0.1/V
CC
x 0.9 @ 5MHz, SO =
Open, CS =
V
SS
SCK = V
CC
x 0.1/V
CC
x 0.9 @ 5MHz, SO =
Open, CS =
V
SS
CS = V
CC
, V
IN
=
V
SS
or V
CC
V
IN
=
V
SS
to V
CC
V
OUT
=
V
SS
to V
CC
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
V
CC
– 0.8
V
CC
– 0.4
V
CC
– 0.2
V
IL
(1)
V
IH
(1)
V
OL1
V
OL2
V
OL3
V
OH1
V
OH2
V
OH3
–0.5
V
CC
x 0.7
V
CC
x 0.3
V
CC
+ 0.5
0.4
0.4
0.4
V
CC
> 3.3V, I
OL
= 2.1mA
2V < V
CC
=
3.3V, I
OL
= 1mA
V
CC
=
2V, I
OL
= 0.5mA
V
CC
> 3.3V, I
OH
= -1.0mA
2V < V
CC
=
3.3V, I
OH
= -0.4mA
V
CC
=
2V, I
OH
= -0.25mA
7033 FRM T06
POWER-UP TIMING
Symbol
t
PUR
(2)
t
PUW
(2)
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Units
ms
ms
7033 FRM T07
Notes:
(1)V
IL
Min. and V
IH
Max. are for reference only and are not 100% tested.
(2)t
PUR
and t
PUW
are the delays required from the time V
CC
is stable until the specified operation can be initiated. These parameters
are periodically sampled and not 100% tested.
8
ICMIC [ IC MICROSYSTEMS ]
