欢迎访问ic37.com |
会员登录 免费注册
发布采购

MHF2815D 参数 Datasheet PDF下载

MHF2815D图片预览
型号: MHF2815D
PDF下载: 下载PDF文件 查看货源
内容描述: 仅0.33英寸( 8.38毫米)高在密闭壳体 [Only 0.33 inches (8.38 mm) high in a hermetically sealed case]
分类和应用: 模拟IC信号电路
文件页数/大小: 23 页 / 1294 K
品牌: INTERPOINT [ INTERPOINT CORPORATION COMPANY ]
 浏览型号MHF2815D的Datasheet PDF文件第2页浏览型号MHF2815D的Datasheet PDF文件第3页浏览型号MHF2815D的Datasheet PDF文件第4页浏览型号MHF2815D的Datasheet PDF文件第5页浏览型号MHF2815D的Datasheet PDF文件第6页浏览型号MHF2815D的Datasheet PDF文件第7页浏览型号MHF2815D的Datasheet PDF文件第8页浏览型号MHF2815D的Datasheet PDF文件第9页  
Crane aerospace & electronics Power solutions
MHF+ Single, dual and triple dC/dC Converters
28 VOlT inPuT – 15 WATT
Features
Only 0.33 inches (8.38 mm) high in a
hermetically sealed case
ModelS
dual
±5
±12
±15
input voltage 16 to 40 vdC
- MHF+281r9S 20 to 32 vdC
- triple output models16 to 48 vdC
transient protection
- Single and dual: 50 v for 50 ms
- triple: 80 v for 120 ms
Fully isolated
Fixed high frequency switching
operating temperature –55° to +125°C
VDC O
utput
Single
1.9
3.3
5
5.2
5.3
12
15
28
triPle
+5 & ±12
+5 & ±15
inhibit and synchronization functions
indefinite short circuit protection
up to 84% efficiency
the MHF+ Single and dual Series™ of high frequency dC/
dC converters offers a wide input voltage range of 16 to 40
volts (MHF+281r9S, 20 to 32 volts) and up to 15 watts of
output power. the units are capable of withstanding short
term transients up to 50 volts. the converters are offered with
standard screening, “eS” screening, or fully compliant to “883”
Mil-PrF-38534 Class H screening. Standard microcircuit
drawings (SMd) are available.
DESCRIPTION
MHF+ Single and dual dC/dC ConverterS
enabled when the pin, which is internally connected to a pull-up
resistor, is left unconnected or is connected to an open-collector
gate. the open circuit output voltage associated with the inhibit
pin is 8.5 to 12 v. in the inhibit mode, a maximum of 4 ma must
be sunk from the inhibit pin. See Figure 3.
s
ynChronization
C
onverter
D
esign
the MHF+ converters are switching regulators that use a
quasi-square wave, single-ended forward converter design with
a constant switching frequency of 550 kHz typical. isolation
between input and output circuits is provided with a transformer
in the forward path and a temperature compensated optical link
in the feedback control loop. See Figure 1.
For the MHF+ dual output models, good cross regulation is
maintained by tightly coupled output magnetics. up to 90%
of the total output power (80% on 2805d) is available from
either output, providing the opposite output is simultaneously
carrying 10% of the total output power (20% on 2805d models).
Predictable current limit is accomplished by directly monitoring
the output load current and providing a constant current output
above the overload point.
an external synchronization feature is included that allows the
user to adjust the nominally 550 kHz operating frequency to
any frequency within the range of 500 kHz to 600 kHz. this is
initiated by applying a signal input of the desired frequency to
pin 5. the capacitively coupled sync input will synchronize on
a differential signal of as low as 4 volts to as high as 5 v. For
single and dual output models, if the sync function is not used,
connect the terminal to input common.
s
hort
C
irCuit
P
roteCtion
MHF+ Series single and dual output converters provide short
circuit protection by restricting the output current to approximately
115% of the
full load output current. the output current is sensed in the
secondary stage to provide highly predictable and accurate
current limiting, and to eliminate foldback characteristics.
u
nDervoltage
l
oCkout
i
nhibit
F
unCtion
MHF+ converters provide an inhibit terminal that can be used to
disable internal switching, resulting in no output current and very
low quiescent input current. the converter is inhibited when an
active low of ≤0.8 V is applied to the inhibit pin. The unit is
Crane aerospace & electronics
electronics group (interpoint Brand)
PO Box 97005 • Redmond WA 98073-9705
425.882.3100 • power@crane-eg.com
www.interpoint.com
undervoltage lockout prevents the single and dual output
converters from operating below approximately 14 vdC input
voltage to keep system current levels smooth, especially during
initialization or re-start operations.
Page 1 of 23
MHF+ rev l - 20091113