HS-26CT31RH-T
Data Sheet
July 1999
File Number
4590.1
Radiation Hardened
Quad Differential Line Driver
Intersil’s Satellite Applications Flow™ (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large
volume satellite manufacturers, while maintaining a high
level of reliability.
The Intersil HS-26CT31RH-T is a Quad Differential Line Driver
designed for digital data transmission over balanced lines and
meets the requirements of EIA Standard RS-422. Radiation
Hardened CMOS processing assures low power consumption,
high speed, and reliable operation in the most severe radiation
environments.
The HS-26CT31RH-T accepts TTL inputs and converts them to
RS-422 compatible outputs. This circuit uses special outputs
that enable the drivers to power down without loading down the
bus. Enable and disable pins allow several devices to be
connected to the same data source and addressed
independently.
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose . . . . . . . . . . . . . . . . . . . . 1 x 10
5
RAD(Si)
- SEU and SEL . . . . . . . . . . Immune to 100MeV/mg/cm
2
• EIA RS-422 Compatible Outputs (Except for IOS)
• TTL Compatible Inputs
• High Impedance Outputs when Disabled or Powered
Down
• Low Power Dissipation 2.75mW Standby (Max)
• Single 5V Supply
• Low Output Impedance 10Ω or Less
• Full -55
o
C to 125
o
C Military Temperature Range
Pinouts
HS1-26CT31RH-T (SBDIP), CDIP2-T16
TOP VIEW
AIN 1
16 V
DD
15 DIN
14 DO
13 DO
12 ENABLE
11 CO
10 CO
9 CIN
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-26CT31RH-T
are contained in SMD 5962-95632.
A “hot-link” is provided
from our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/quality/manuals.asp
AO 2
AO 3
ENABLE 4
BO 5
BO 6
BIN 7
GND 8
HS9-26CT31RH-T (FLATPACK), CDFP4-F16
TOP VIEW
AIN
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
DIN
DO
DO
ENABLE
CO
CO
CIN
Ordering Information
ORDERING
NUMBER
5962R9563201TEC
HS1-26C31RH/Proto
5962R9563201TXC
HS9-26C31RH/Proto
PART
NUMBER
HS1-26CT31RH-T
HS1-26C31RH/Proto
HS9-26C31RH-T
HS9-26C31RH/Proto
TEMP.
RANGE
(
o
C)
-55 to 125
-55 to 125
-55 to 125
-55 to 125
AO
AO
ENABLE
BO
BO
BIN
GND
NOTE:
Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.
INTERSIL [ INTERSIL CORPORATION ]
