HIP6021A
Data Sheet
November 1999
File Number
4793
Advanced PWM and Triple Linear Power
Controller
The HIP6021A provides the power control and protection for
four output voltages in high-performance, graphics intensive
microprocessor and computer applications. The IC
integrates a voltage-mode PWM controller and three linear
controllers, as well as the monitoring and protection
functions into a 28 lead SOIC package.
The synchronous-rectified buck converter includes an Intel-
compatible, TTL 5-input digital-to-analog converter (DAC)
that adjusts the core PWM output voltage from 1.3V
DC
to
2.05V
DC
in 0.05V steps and from 2.1V
DC
to 3.5V
DC
in 0.1V
increments. The precision reference and voltage-mode
control provide
±1%
static regulation. A TTL-compatible
signal applied to the SELECT pin dictates which method of
control is used for the AGP bus power: a low state results in
linear control of the AGP bus to 1.5V, while a high state
transitions the output through a linearly controlled softstart to
3.3V, followed by full enhancement of the external MOSFET
to pass the input voltage. The other two linear regulators
provide fixed output voltages of 1.5V GTL bus power and
1.8V power for the North/South Bridge core and/or cache
memory. These levels are user-adjustable by means of an
external resistor divider and pulling the FIX pin low. All linear
controllers can employ either N-Channel MOSFETs or
bipolar NPNs for the pass transistor.
The HIP6021A monitors all the output voltages. A single
Power Good signal is issued when the core is within
±10%
of
the DAC setting and all other outputs are above their under-
voltage levels. Additional built-in over-voltage protection for
the core output uses the lower MOSFET to prevent output
voltages above 115% of the DAC setting. The PWM
controller’s over-current function monitors the output current
by using the voltage drop across the upper MOSFET’s
r
DS(ON)
.
Features
• Provides 4 Regulated Voltages
- Microprocessor Core, AGP Bus, Memory, and GTL Bus
Power
• Drives N-Channel MOSFETs
• Linear Regulator Drives Compatible with both MOSFET
and Bipolar Series Pass Transistors
• Fixed or Externally Resistor-Adjustable Linear Outputs
• Simple Single-Loop Control Design
- Voltage-Mode PWM Control
• Fast PWM Converter Transient Response
- High-Bandwidth Error Amplifier
- Full 0% to 100% Duty Ratio
• Excellent Output Voltage Regulation
- Core PWM Output:
±1%
Over Temperature
- Other Outputs:
±3%
Over Temperature
• TTL-Compatible 5-Bit DAC Core Output Voltage Selection
- Shutdown Feature Removed When All Inputs High
- Wide Range 1.3V
DC
to 3.5V
DC
• Power-Good Output Voltage Monitor
• Over-Voltage and Over-Current Fault Monitors
- Switching Regulator Does Not Require Extra Current
Sensing Element, Uses Upper MOSFET’s r
DS(ON)
• Small Converter Size
- Constant Frequency Operation
- 200kHz Free-Running Oscillator; Programmable From
50kHz to Over 1MHz
- Small External Component Count
Applications
• Motherboard Power Regulation for Computers
Pinout
HIP6021A (SOIC)
TOP VIEW
DRIVE2 1
28 VCC
27 UGATE
26 PHASE
25 LGATE
24 PGND
23 OCSET
22 VSEN1
21 FB
20 COMP
19 VSEN3
18 DRIVE3
17 GND
16 VAUX
15 DRIVE4
Ordering Information
PART NUMBER
HIP6021ACB
HIP6021EVAL1
TEMP.
RANGE (
o
C)
0 to 70
PACKAGE
28 Ld SOIC
PKG.
NO.
M28.3
FIX 2
VID4 3
VID3 4
VID2 5
VID1 6
Evaluation Board
VID0 7
PGOOD 8
SD 9
VSEN2 10
SELECT 11
SS 12
FAULT/RT 13
VSEN4 14
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 407-727-9207
|
Copyright
©
Intersil Corporation 1999
INTERSIL [ INTERSIL CORPORATION ]
