HIP6301
Absolute Maximum Ratings
Supply Voltage, V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V
Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to V
CC
+ 0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5kV
Thermal Information
Thermal Resistance (Typical, Note 1)
θ
JA
(°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . .-65
o
C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
Recommended Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V
±5%
Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTE:
1.
θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
PARAMETER
INPUT SUPPLY POWER
Input Supply Current
Operating Conditions: V
CC
= 5V, T
A
= 0°C to 70°C, Unless Otherwise Specified
TEST CONDITIONS
MIN
TYP
MAX
UNITS
R
T
= 100kΩ
EN = 0V
-
4.25
4.25
3.75
10
8.8
4.38
3.88
15
4.5
4.5
4.00
mA
mA
V
V
POR (Power-On Reset) Threshold
V
CC
Rising
V
CC
Falling
REFERENCE AND DAC
System Accuracy
DAC (VID0 - VID3) Input Low Voltage
DAC (VID0 - VID3) Input High Voltage
VID Pull-Up
Percent system deviation from programmed VID Codes
DAC Programming Input Low Threshold Voltage
DAC Programming Input High Threshold Voltage
VIDx = 0V or VIDx = 3V
-1
-
2.0
10
-
-
-
20
1
0.8
-
40
%
V
V
µA
CHANNEL GENERATOR, SAWTOOTH GENERATOR and Maximum PWM Duty Cycle
Frequency, F
SW
Adjustment Range
Disable Voltage
Sawtooth Amplitude
PWM Maximum Duty Cycle
ERROR AMPLIFIER
DC Gain
Gain-Bandwidth Product
Slew Rate
Maximum Output Voltage
Minimum Output Voltage
I
SEN
Full Scale Input Current
Overcurrent Trip Level
POWER GOOD MONITOR
Undervoltage Threshold
Undervoltage Threshold
PGOOD Low Output Voltage
VSEN Rising
VSEN Falling
I
PGOOD
= 4mA
-
-
-
0.92
0.90
0.18
-
-
0.4
V
DAC
V
DAC
V
-
-67.5
50
-
-
-87.5
µA
µA
R
L
= 10K to ground
C
L
= 100pF, R
L
= 10K to ground
C
L
= 100pF, R
L
= 10K to ground
R
L
= 10K to ground
R
L
= 10K to ground
-
-
-
3.6
-
72
18
5.3
4.1
0.16
-
-
-
-
0.5
dB
MHz
V/µs
V
V
R
T
= 100kΩ,
±1%
See Figure 10
Maximum voltage at FS/DIS to disable controller. I
FS/DIS
= 1mA.
Amplitude of Sawtooh Generator at Channel Comparator Input
224
0.05
-
-
-
280
-
1.2
1.33
75
336
1.5
1.0
-
-
kHz
MHz
V
Vp-p
%
6
FN4765.6
December 27, 2004
INTERSIL [ INTERSIL CORPORATION ]
