Data Sheet No. PD60166 revS
IR2136/IR21362/IR21363/IR21365/
IR21366/IR21367/IR21368 (J&S) & (PbF)
Features
•
•
•
•
•
•
•
•
•
•
•
•
Floating channel designed for bootstrap operation
3-PHASE BRIDGE DRIVER
Packages
Fully operational to +600V
Tolerant to negative transient voltage - dV/dt immune
Gate drive supply range from 10 to 20V (IR2136/IR21368),
11.5 to 20V (IR21362) or 12 to 20V (IR21363/IR21365/
IR21366/IR21367)
Undervoltage lockout for all channels
28-Lead SOIC
Over-current shutdown turns off all six drivers
Independent 3 half-bridge drivers
28-Lead PDIP
Matched propagation delay for all channels
Cross-conduction prevention logic
44-Lead PLCC w/o 12 leads
Lowside outputs out of phase with inputs. High side
outputs out of phase (IR2136/IR21363/IR21365/
Feature Comparison: IR2136/IR21362/IR21363/
IR21366/IR21367/IR21368) or in phase
IR21365/IR21366/IR21367/IR21368
(IR21362) with inputs.
3.3V logic compatible
Part
IR2136 IR21362 IR21363 IR21365 IR21366 IR21367 IR21368
Lower di/dt gate driver for
Input Logic HIN, LIN HIN/LIN HIN, LIN HIN, LIN HIN, LIN HIN, LIN HIN,LIN
better noise immunity
400ns
Ton (typ.)
400ns
250ns
400ns
400ns
400ns
250ns
Externally programmable
Toff (typ.)
380ns
380ns
180ns
380ns
380ns
380ns
180ns
delay for automatic fault
V
IH
(typ.)
2.7V
2.0V
2.0V
2.7V
2.7V
2.7V
2.0V
clear
V
IL
(typ.)
1.7V
1.3V
1.3V
1.7V
1.7V
1.7V
1.3V
Also available LEAD-FREE
Vitrip+
4.3V
4.3V
0.46V
0.46V
0.46V
0.46V
4.3V
UV CC/BS+ 8.9V
UV CC/BS- 8.2V
10.4V
9.4V
11.2V
11.0V
11.2V
11.0V
11.2V
11.0V
11.2V
11.0V
8.9V
8.2V
Description
The IR2136/IR21362/IR21363/IR21365/IR21366/IR21367/IR21368(J&S) are high votage, high speed power MOSFET
and IGBT drivers with three independent high and low side referenced output channels for 3-phase applications.
Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS
or LSTTL outputs, down to 3.3V logic. A current trip function which terminates all six outputs can be derived from
an external current sense resistor. An enable function is available to terminate all six outputs simultaneously. An
open-drain FAULT signal is provided to indicate that an overcurrent or undervoltage shutdown has occurred.
Overcurrent fault conditions are cleared automatically after a delay programmed externally via an RC network
connected to the RCIN input. The output drivers feature a high pulse current buffer stage designed for minimum
driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The
floating channel can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which
operates up to 600 volts.
Typical Connection
VCC
HIN1,2,3 / HIN1,2,3
LIN1,2,3
FAULT
VCC
HIN1,2,3 / HIN1,2,3
LIN1,2,3
HO1,2,3
FAULT
EN
VS1,2,3
VB1,2,3
up to 600V
(Refer to Lead Assign-
ments for correct pin con-
figuration). This/These
diagram(s) show electri-
cal connections only.
Please refer to our Appli-
cation
Notes
and
DesignTips for proper cir-
cuit board layout.
EN
RCIN
ITRIP
VSS
LO1,2,3
COM
TO
LOAD
IR2136(2)(3)(5)(6)(7)(8)
GND
www.irf.com
1
IRF [ INTERNATIONAL RECTIFIER ]
