MIL-C-81659
Cannon's DPXNA (non-environmental, Type IV) and
DPXNE (environmental, Types II and III) rack and
panel connectors are designed to meet or exceed
the requirements of MIL-C-81659, Revision B. They
are used in military and aerospace applications and
computer periphery equipment requirements, and
are designed to operate in temperatures ranging
from - 65˚C to + 125˚C. DPXNA/NE connectors
are available in single, 2, 3, and 4 gang config-
urations, with a total of 12 contact arrangements
accommodation contact sizes 12, 16, 20 and 22,
and combination standard and coaxial contacts.
DPXNA/DPXNE
Contact retention of these crimp snap-in contacts is
provided by the LITTLE CAESAR® rear release
contact retention assembly. Environmental sealing
is accomplished by wire sealing grommets and
interfacial seals.
How to Order
Single Gang
DPX
B
NE - A106 - 33
P - 00
SERIES PREFIX
SHELL STYLE
CLASS
CONTACT ARRANGEMENT
SHELL TYPE
CONTACT TYPE
MODIFICATION
Two (2) Gang
DPX
2
NE - 67M
P
AW8
P
34
B - 00
SERIES PREFIX
DPX - ITT Cannon Designation
SHEL STYLE
B - ARINC 'B' Shell
CLASS (MIL-C-81659B, Class 1)....
NA - Non - Environmental (MIL-C-81659B, Type IV)
NE - Environmental (Mil-C-81659B, Types II and
III)
INSERT DESIGNATOR
In the 3 and 4 gang assemblies, the insert desig-
nation number represents cumulative (total) con-
tacts. The charts on page 26 denote shell cavity
location by layout. (If desired arrangement location
is not defined, please consult or local sales
engineering office.)
CONTACT ARRANGEMENT
See page 31
SHELL TYPE
'33' for Plug; '34' for Receptacle
CONTACT TYPE
'P' for Pin (Standard on '34' receptacle except
A106 layout which has reversed contact sex)
'S' for Socket (Standard on '33' plug except A106
layout which has reversed contact sex)
MODIFICATION CODES
- 00 Standard
- 01 Standard with clinch nuts in the mounting
holes (34 only).
- 02 Standard with tabs for attaching junction
shells.
- 03 Standard with mounting holes .120 dia.
countersunk 100˚ to . 230 dia. (33. only).
- 17 Combination of 01** and 02** (clinch
nuts in mounting holes - 34 only and tabs
for attaching junction shells).
- 22 Standard with clinch nuts (.33 only).
- 23 Standard with standard floating eyelets.
- 29 Standard except less grommet (NE, pin
only).
- 30 Same as - 29** except with tabs for
attaching junction shells.
- 33 Same as - 29** except with clinch nuts.
- 37 Same as - 29** except with clinch nuts
and tabs for attacting
junction shells.
- 39 Standard with standard floating eyelets
and tabs for attaching junction shells.
NOTE:
For additional modification codes please consult the
factory
SERIES PREFIX
TWO (2) GANG SHELL
CLASS
CONTACT ARRANGEMENT (Side A)
CONTACT TYPE
CONTACT ARRANGEMENT (Side B)
CONTACT TYPE
SHELL TYPE
SHELL STYLE
MODIFICATION
Three (3) Gang
DPX 3
NE
-
240M
-
33
PS
-
00
SERIES PREFIX
THREE (3) GANG SHELL
CLASS
INSERT DESIGNATOR
SHELL TYPE
CONTACT TYPE
MODIFCATION
Four (4) Gang
DPX
4
NE
-
104M
-
34
P
-
00
SERIES PREFIX
FOUR (4) GANG SHELL
CLASS
INSERT DESIGNATOR
SHELL TYPE
CONTACT TYPE
MODIFICATION
NOTE:
On 3 & 4 gang assemblies, combination layouts, the contact type designator of the A106 layout. If applicable, precedes the
designator for standard contact sex layouts. See three (3) gang nomenclature breakdown above for 240M example (67MS, 67 MS,
A106P).
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
25
ITT [ ITT INDUSTRIES ]
