FORM 1468 (REV. B) 9/00
INSTALLATION INSTRUCTIONS
®
HYFIRE
®
VIIS SPORTSMAN
CD IGNITION SYSTEM
Notice: This product is legal for sale or use only on vehicles which may never be used on highways.
The HYFIRE
®
VII
S
Sportsman CD Ignition Controls are not compatible with distributorless systems or
positive ground applications. The RPM Limiter in the HYFIRE
®
VII
S
Sportsman CD Ignition Controls will not
work properly with odd-fire or semi-even fire V6 applications. The HYFIRE
®
VII
S
Ignition System is not
designed for marine use.
Part No. 667S
412 Cylinder
The RPM limiter in the HYFIRE
®
VIIS Ignition System is not recommended as
an engine speed governor. The use of the RPM limiters is not recommended for
applications equipped with a catalytic converter. Similarly, forcing engine RPM
past the RPM limiter continuously for long sustained intervals can cause
problems resulting from fuel build up in the exhaust system that may adversely
affect the application.
GENERAL INFORMATION
Spark Plug Gaps
For street applications, use your engine manufacturers specifications. For racing
applications, start with your engine manufacturers specifications, then experi-
ment with the plug gap to achieve maximum performance.
Disconnect the HYFIRE
®
VIIS Ignition System and unplug any distributor
harnesses (if possible) before any welding is done on the vehicle.
Electric Welding
Ignition Ballast Resistor / Loom Resistance Wire
The HYFIRE
®
VIIS Ignition Ignitions performance is not affected by the presence
of the factory ignition resistors or ignition ballast resistors in the wire from the
External RPM Limiters
ignition switch. It is not necessary to install ignition ballast resistors as specified Mallory RPM Limiter Part Nos. 641-4, 641-6, 641-8, 642, 643 and 644 WILL
NOT function with the HYFIRE
®
VII Ignition Systems.
by the instructions for the particular distributor.
Ignition Coils
®
The HYFIRE
®
VIIS Ignition System is designed to work with Mallory The tachometer and shift light will work with the HYFIRE VII Ignition Systems.
®
PROMASTER
®
Coil Part No. 28880. Avoid using any other type of ignition coil. However, the RPM limiter WILL NOT function with the HYFIRE VII Ignition
Systems. Turn the LIMIT RPM knob slightly past 11,000 to prevent the RPM
Spark Plug Wires
limiter from interfering with the tachometers other functions.
YOU MUST USE suppression type (carbon core, spiral core) spark plug wire.
We recommend spiral core ignition wire, such as Mallory PRO SIDEWINDER
®
Ignition Wire. Suppression type spark plug wires prevent false triggering and the
possibility of premature ignition or accessory failures.
Mallory PRO TACH
®
I, IV and IV
DO NOT USE solid core (copper core; stainless steel core) spark plug wire with
any electronic ignition system or accessory. Solid core spark plug wire is a
source of ignition noise, which can cause false triggering and premature ignition
or accessory failure.
MOUNTING PROCEDURE
Step 1
Step 2
Disconnect the battery () cable to cut power to the system.
Step 3
Mounting to a flat surface with shock mounts
Hold the unit in its mounting position and center punch the mounting pattern on
the mounting surface for drilling mounting holes. Drill mounting holes using a 9/
32" drill bit.
Select a convenient location to mount the HYFIRE
®
VIIS Ignition System. Keep
the unit away from hot engine components or extreme heat such as the exhaust Install the shock mounts into the bottom plate of the unit. Hold the unit in position
where it will be mounted.
system and manifolds. Keep the unit away from moving devices, such as fans,
belts and linkages. The location must be dry. Moisture will damage components From the backside of the mounting surface, insert the washers and the 1/4-20
nylock nuts onto the shock mount studs. Tighten each nut until snug.
inside the unit.
1