100W Single Output Switching Power Supply
Features :
PLN-100
series
Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage / Over temperature
Built-in active PFC function
IP64 design for indoor or outdoor installations
UL1310 Class 2 power unit
Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
2 years warranty
F
110
M
M
SELV
EQUIVALENT
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
CURRENT ADJ. RANGE
VOLTAGE TOLERANCE
Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR (Typ.)
INPUT
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER CURRENT
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY &
EMC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
Note.4
LPS
PLN-100-20
20V
10 ~ 20V
4.8A
0 ~ 4.8A
96W
150mVp-p
( for 48V only)
( except for 48V )
IP64
PLN-100-36
36V
18 ~ 36V
2.65A
0 ~ 2.65A
95.4W
150mVp-p
PLN-100-48
48V
24 ~ 48V
2A
0 ~ 2A
96W
200mVp-p
PLN-100-12
12V
Note.6
5A
Note.6
0 ~ 5A
Note.6
60W
PLN-100-15
15V
7.5 ~ 15V
5A
0 ~ 5A
75W
150mVp-p
PLN-100-24
24V
12 ~ 24V
4A
0 ~ 4A
96W
150mVp-p
PLN-100-27
27V
13.5 ~ 27V
3.55A
0 ~ 3.55A
95.85W
150mVp-p
CONSTANT CURRENT REGION
Note.7
6 ~ 12V
RIPPLE & NOISE (max.)
Note.2
150mVp-p
0% ~ -15%. Can be adjusted by internal potential meter SVR1
3% ~ -25%. Can be adjusted by internal potential meter SVR2
3.0%
1.0%
2.0%
1200ms, 80ms/230VAC 1200ms, 80ms/115VAC at full load
60ms/230VAC 30ms/115VAC at full load
Note.5
90 ~ 264VAC
3.0%
3.0%
3.0%
3.0%
2.0%
2.0%
127 ~ 370VDC
PF>0.95/115VAC at full load
85%
87%
87%
87%
0.45A/230VAC
87%
20V ~ 48V:1.1A/115VAC
87%
0.55A/230VAC
15V:0.9A/115VAC
47 ~ 63Hz
PF>0.95/230VAC
83%
12V:0.8A/115VAC 0.4A/230VAC
COLD START 40A/230VAC
0.5mA / 240VAC
95 ~ 100%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
13 ~ 16V
16.5 ~ 20V
22 ~ 27V
27 ~ 34V
29 ~ 36V
39 ~ 48V
Protection type : Shut down and latch off o/p voltage, re-power on to recover
90
10
(RTH2)
(Refer to output load derating curve)
Protection type : Shut down o/p voltage, re-power on to recover
-30 ~ +50
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH
0.03%/
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
52 ~ 64V
UL1310 Class 2, UL879 ( listed in UL Sign Components Manual (SAM) ), TUV EN60950-1, EN61347-1, EN61347-2-13
CAN/CSA C22.2 No. 223-M91(except for 48V), IP64 approved
I/P-O/P:4.25KVDC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH
EMI CONDUCTION & RADIATION
Compliance to EN55015, EN55022 (CISPR22) Class B
HARMONIC CURRENT
Compliance to EN61000-3-2 Class C (>50% load) ; EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN61547, EN55024, light industry level, criteria A
EMS IMMUNITY
MTBF
303.1Khrs min. MIL-HDBK-217F (25 )
DIMENSION
PACKING
200*70.5*35mm (L*W*H)
0.52Kg; 20pcs/11.4Kg/0.76CUFT
OTHERS
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to OLP characteristics.
5. Derating may be needed under low input voltage. Please check the derating curve for more details.
6. This is the maximum possible output current and power. Over load protection may be activated slightly below this level to comply with the requirement
of UL1310 class 2.
7. Constant current operation region is within 50% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
File Name:PLN-100-SPEC 2008-08-18
MEANWELL [ MEAN WELL ENTERPRISES CO., LTD. ]
