100W Single Output DC-DC Converter
Features :
2:1 wide input range
SD-100
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
Fixed switching frequency at 83KHz
24V and 48V input voltage design refer to LVD
Low cost
High reliability
2 years warranty
series
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE
Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
EFFICIENCY (Typ.)
INPUT
DC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVERLOAD
PROTECTION
OVER VOLTAGE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY & WITHSTAND VOLTAGE
EMC
(Note 4)
(for D type only)
SD-100B-5
5V
20A
0 ~ 20A
100W
4.5 ~ 5.5VDC
2.0%
0.5%
0.5%
2s, 50ms(only D mode) at full load
20ms(only D mode) at full load
B:19 ~ 36VDC
74%
4.8A/24V
D:18A/96VDC
<0.75mA/120VAC(SD-100D)
105 ~ 135% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
5.75 ~ 6.75V/10% load
16.8 ~ 20V/10% load
Protection type : Hiccup mode, recovers automatically after fault condition is removed
-10 ~ +60
-20 ~ +85
(Refer to output load derating curve)
, 10 ~ 95% RH
20 ~ 90% RH non-condensing
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
IEC60950-1 CB approved by TUV (for D type only)
I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
/ 70% RH
75%
2.4A/48V
C:36 ~ 72VDC
76%
1.8A/96V
D:72 ~ 144VDC or 85 ~ 132VAC
75%
4.8A/24V
77%
2.4A/48V
80%
1.8A/96V
78%
4.8A/24V
81%
2.4A/48V
83%
1.8A/96V
SD-100C-5
SD-100D-5
SD-100B-12 SD-100C-12 SD-100D-12 SD-100B-24 SD-100C-24 SD-100D-24
12V
8.5A
0 ~ 8.5A
102W
120mVp-p
11 ~ 16VDC
1.0%
0.3%
0.3%
24V
4.2A
0 ~ 4.2A
100.8W
150mVp-p
23 ~ 30VDC
1.0%
0.2%
0.2%
RIPPLE & NOISE (max.)
Note.2
100mVp-p
31.5 ~ 37.5V/10% load
ISOLATION RESISTANCE
EMS IMMUNITY
MTBF
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
EMI CONDUCTION & RADIATION
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-4-2,3,4,6,8; ENV50204, light industry level, criteria A
356.7K hrs min.(SD-100B)
355.5K hrs min.(SD-100C)
199*98*38mm (L*W*H)
0.65Kg; 20pcs/13.8Kg/0.8CUFT
341.9K Hrs min.(SD-100D)
MIL-HDBK-217F (25
)
OTHERS
DIMENSION
PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.
(as available on http://www.meanwell.com)
File Name:SD-100-SPEC 2010-10-18
MEANWELL [ MEAN WELL ENTERPRISES CO., LTD. ]
