4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
PIN DESCRIPTIONS
44-PIN SOP 40-PIN TSOP 48-PIN TSOP
NUMBERS NUMBERS NUMBERS SYMBOL
43
9
11
WE#
TYPE
Input
DESCRIPTION
Write Enable: Determines if a given cycle is a WRITE
cycle. If WE# is LOW, the cycle is either a WRITE to the
command execution logic (CEL) or to the memory array.
Write Protect: Unlocks the boot block when HIGH if V
PP
= V
PPH
1
(3.3V) or V
PPH
2
(5V) and RP# = V
IH
during a
WRITE or ERASE. Does not affect WRITE or ERASE
operation on other blocks.
Chip Enable: Activates the device when LOW. When
CE# is HIGH, the device is disabled and goes into
standby power mode.
Reset/Power-Down: When LOW, RP# clears the status
register, sets the internal state machine (ISM) to the
array read mode and places the device in deep power-
down mode. All inputs, including CE#, are “Don’t
Care,” and all outputs are High-Z. RP# unlocks the boot
block and overrides the condition of WP# when at V
HH
(12V), and must be held at V
IH
during all other modes
of operation.
Output Enable: Enables data output buffers when
LOW. When OE# is HIGH, the output buffers are
disabled.
Byte Enable: If BYTE# = HIGH, the upper byte is active
through DQ8–DQ15. If BYTE# = LOW, DQ8–DQ14 are
High-Z, and all data is accessed through DQ0–DQ7.
DQ15/(A-1) becomes the least significant address input.
Address Inputs: Select a unique, 16-bit word or 8-bit
byte. The DQ15/(A-1) input becomes the lowest order
address when BYTE# = LOW (MT28F400B3) to allow for
a selection of an 8-bit byte from the 524,288 available.
2
12
14
WP#
Input
12
22
26
CE#
Input
44
10
12
RP#
Input
14
24
28
OE#
Input
33
–
47
BYTE#
Input
11, 10, 9, 8, 21, 20, 19,
7, 6, 5, 4, 18, 17, 16,
42, 41, 40, 15, 14, 8, 7,
39, 38, 37, 36, 6, 5, 4, 3,
36, 35, 34, 3 2, 1, 40, 13
31
–
15, 17, 19,
21, 24, 26,
28, 30
16, 18, 20,
22, 25, 27,
29
1
23
13, 32
–
Input/ Data I/O: MSB of data when BYTE# = HIGH. Address
Output Input: LSB of address input when BYTE# = LOW during
READ or WRITE operation.
25-28, 32-35 29, 31, 33, DQ0–DQ7
Input/ Data I/Os: Data output pins during any READ operation
35, 38, 40,
Output or data input pins during a WRITE. These pins are used
42, 44
to inputcommands to the CEL.
–
30, 32, 34, DQ8–DQ14
Input/ Data I/Os: Data output pins during any READ operation
36, 39, 41,
Output or data input pins during a WRITE when BYTE# = HIGH.
43
These pins are High-Z when BYTE# is LOW.
11
13
V
PP
Supply Write/Erase Supply Voltage: From a WRITE or ERASE
CONFIRM until completion of the WRITE or ERASE, V
PP
must be at V
PPH
1
(3.3V) or V
PPH
2
(5V). V
PP
= “Don’t Care”
during all other operations.
30, 31
37
V
CC
Supply Power Supply: +3.3V ±0.3V.
23, 39
27, 46
V
SS
Supply Ground.
29, 37, 38 9, 10, 15, 16
NC
–
No Connect: These pins may be driven or left
unconnected.
25, 24, 23,
22, 21, 20,
19, 18, 8, 7,
6, 5, 4, 3, 2,
1, 48, 17
45
A0–A17/
(A18)
Input
DQ15/
(A-1)
4Mb Smart 3 Boot Block Flash Memory
F45_3.p65 – Rev. 3, Pub. 12/01
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2001, Micron Technology, Inc.