128Mb: x4, x8, x16
SDRAM
PIN DESCRIPTIONS
TSOP PIN NUMBERS
38
SYMBOL
CLK
TYPE
Input
DESCRIPTION
Clock: CLK is driven by the system clock. All SDRAM input signals are
sampled on the positive edge of CLK. CLK also increments the internal
burst counter and controls the output registers.
Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK
signal. Deactivating the clock provides PRECHARGE POWER-DOWN and
SELF REFRESH operation (all banks idle), ACTIVE POWER-DOWN (row
active in any bank) or CLOCK SUSPEND operation (burst/access in
progress). CKE is synchronous except after the device enters power-
down and self refresh modes, where CKE becomes asynchronous until
after exiting the same mode. The input buffers, including CLK, are
disabled during power-down and self refresh modes, providing low
standby power. CKE may be tied HIGH.
Chip Select: CS# enables (registered LOW) and disables (registered HIGH)
the command decoder. All commands are masked when CS# is regis-
tered HIGH. CS# provides for external bank selection on systems with
multiple banks. CS# is considered part of the command code.
Command Inputs: WE#, CAS#, and RAS# (along with CS#) define the
command being entered.
Input/Output Mask: DQM is an input mask signal for write accesses and
an output enable signal for read accesses. Input data is masked when
DQM is sampled HIGH during a WRITE cycle. The output buffers are
placed in a High-Z state (two-clock latency) when DQM is sampled HIGH
during a READ cycle. On the x4 and x8, DQML (Pin 15) is a NC and
DQMH is DQM. On the x16, DQML corresponds to DQ0-DQ7 and DQMH
corresponds to DQ8-DQ15. DQML and DQMH are considered same state
when referenced as DQM.
Bank Address Inputs: BA0 and BA1 define to which bank the ACTIVE,
READ, WRITE, or PRECHARGE command is being applied.
Address Inputs: A0-A11 are sampled during the ACTIVE command (row-
address A0-A11) and READ/WRITE command (column-address A0-A9,
A11 [x4]; A0-A9 [x8]; A0-A8 [x16]; with A10 defining auto precharge) to
select one location out of the memory array in the respective bank. A10
is sampled during a PRECHARGE command to determine if all banks are
to be precharged (A10 [HIGH]) or bank selected by BA0, BA1 (A10
[LOW]). The address inputs also provide the op-code during a LOAD
MODE REGISTER command.
Data Input/Output: Data bus for x16 (4, 7, 10, 13, 42, 45, 48, and 51 are
NCs for x8; and 2, 4, 7, 8, 10, 13, 42, 45, 47, 48, 51, and 53 are NCs for x4).
Data Input/Output: Data bus for x8 (2, 8, 47, 53 are NCs for x4).
Data Input/Output: Data bus for x4.
No Connect: These pins should be left unconnected.
Address input (A12) for the 256Mb and 512Mb devices
DQ Power: Isolated DQ power on the die for improved noise immunity.
DQ Ground: Isolated DQ ground on the die for improved noise
immunity.
Power Supply: +3.3V ±0.3V.
Ground.
37
CKE
Input
19
CS#
Input
16, 17, 18
39
15, 39
WE#, CAS#,
RAS#
x4, x8: DQM
x16: DQML,
DQMH
Input
Input
20, 21
23-26, 29-34, 22, 35
BA0, BA1
A0-A11
Input
Input
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
2, 5, 8, 11, 44, 47, 50, 53
5, 11, 44, 50
40
36
3, 9, 43, 49
6, 12, 46, 52
1, 14, 27
28, 41, 54
DQ0-DQ15
DQ0-DQ7
DQ0-DQ3
NC
NC
V
DD
Q
V
SS
Q
V
DD
V
SS
x16: I/O
x8: I/O
x4: I/O
–
–
Supply
Supply
Supply
Supply
128Mb: x4, x8, x16 SDRAM
128MSDRAM_E.p65 – Rev. E; Pub. 1/02
8
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2001, Micron Technology, Inc.
MICRON [ MICRON TECHNOLOGY ]
