MT9T001 - 1/2-Inch 3-Megapixel Digital Image Sensor
Features
1/2-Inch 3-Megapixel CMOS Digital
Image Sensor
MT9T001P12STC
For the latest data sheet, refer to Micron’s Web site:
Features
•
•
•
•
•
•
•
•
•
DigitalClarity™ Image sensor technology
High frame rate
Global reset release
Horizontal and vertical binning
Column and row skip modes
Superior low-light performance
Low dark current
Simple two-wire serial interface
Programmable controls: Gain, frame rate, frame
size, exposure
• Pin-for-pin compatible with Micron’s 1.3-megapixel
MT9M001 and 2-megapixel MT9D001
Table 1:
Key Performance Parameters
Typical Value
1/2-inch (4:3)
6.55mm(H) x 4.92mm(V)
8.19 (Diagonal)
2,048H x 1,536V
3.2μm x 3.2μm
RGB Bayer pattern
Global reset release (GRR),
electronic rolling shutter (ERS)
48 MPS/48 MHz
Programmable up to 12 fps
Programmable up to 20 fps
Programmable up to 27 fps
Programmable up to 43 fps
Programmable up to 93 fps
10-bit, on-chip
>1.0 V/lux-sec (550nm)
61dB
43dB
3.0V
−
3.6V (3.3V nominal)
240mW (nominal);
2µW (standby)
0°C to +60°C
48-pin PLCC
Parameter
Optical format
Active imager size
Active pixels
Pixel size
Color filter array
Shutter type
Maximum data rate/
master clock
QXGA
(2,048 x 1,536)
UXGA
Frame (1,600 x 1,200)
rate
SXGA
(1,280 x 1,024)
XGA
(1,024 x 768)
VGA (640 x 480)
ADC resolution
Responsivity
Dynamic range
SNR
MAX
Supply voltage
Power consumption
Operating temperature
Packaging
Applications
• Digital still cameras
• Digital video cameras
• Converged DSCs/camcorders
General Description
The Micron
®
Imaging MT9T001 is a QXGA-format 1/2-
inch CMOS active-pixel digital image sensor with an
active imaging pixel array of 2,048H x 1,536V. It incor-
porates sophisticated camera functions on-chip such
as windowing, column and row skip mode, and snap-
shot mode. It is programmable through a simple two-
wire serial interface.
The 3-megapixel CMOS image sensor features Digital-
Clarity—Micron’s breakthrough low-noise CMOS
imaging technology that achieves CCD image quality
(based on signal-to-noise ratio and low-light sensitiv-
ity) while maintaining the inherent size, cost, and inte-
gration advantages of CMOS.
The sensor can be operated in its default mode or pro-
grammed by the user for frame size, exposure, gain set-
ting, and other parameters. The default mode outputs
a QXGA image at 12 frames per second (fps). An on-
chip analog-to-digital converter (ADC) provides 10 bits
per pixel. FRAME_VALID and LINE_VALID signals are
output on dedicated pins, along with a pixel clock that
is synchronous with valid data.
81004bad/80ffb422
MT9T001_3100_DS_1.fm - Rev. D 7/05 EN
The MT9T001 produces extraordinarily clear, sharp
digital pictures, and its ability to capture both continu-
ous video and single frames makes it the perfect choice
for a wide range of consumer and industrial applica-
tions, including digital still cameras, digital video cam-
eras, and PC cameras.
1
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2004 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are for subject to change by Micron without notice.
MICRON [ MICRON TECHNOLOGY ]
