66056
SINGLE/DUAL CHANNEL, HERMETICALLY SEALED, VERY HIGH SPEED OPTOCOUPLER
Rev 1 7/3/01
ELECTRICAL CHARACTERISTICS Ta=-55°C to at 125°C unless otherwise specified.
PARAMETER
SYMBOL MIN TYP MAX UNITS
TEST CONDITIONS
NOTE
High Level Output Current
I
V
5
0.5
250
0.6
µA
V
V
CC
= 5.5V, V = 5.5V,I =250µA
1
OH
O
F
Low Level Output Voltage
High Level Supply Current
Low Level Supply Current
Input Forward Voltage
V = 5.5V, I = 10mA
CC F
1,3
OL
I
(Sinking) = 10mA
OL
Single Channel
Dual Channel
Single Channel
Dual Channel
I
9
14
28
18
36
1.75
mA
mA
V
= 5.5V, I = 0
CCH
CC F
18
13
26
1.5
(Both Channels)
V = 5.5V, I = 20mA
CC
I
CCL
F
(Both Channels)
V
BV
V
V
I
F
= 20mA
1
2
F
Input Reverse Breakdown Voltage
5
I
R
= 10µA
R
Input-Output Insulation Leakage Current
I
1.0
µA
V
I—0
= 1500Vdc,
I—O
Relative Humidity = 45%
t = 25°C, t = 5s
a
Propagation Delay Time To High Output Level
Propagation Delay Time To Low Output Level
t
t
45
55
100
100
ns
ns
R
= 510Ω, C = 50pF.
3,4
3,5
PLH
L
L
I = 13mA, t = 25°C
f
a
R = 510Ω, C = 50pF
PHL
L
L
If = 13mA, t = 25°C
a
°
TYPICAL CHARACTERISTICS TA = 25 C, VCC = 5V EACH CHANNEL
PARAMETER
SYMBOL MIN
TYP
MAX UNITS
TEST CONDITIONS
NOTE
Input Capacitance
Input Diode Temperature Coefficient
Resistance (Input-Output)
C
60
pF
mV/°C
Ω
V
F
= 0, f = MHz
1
1
2
2
IN
∆vF ∆TA
-1.9
I = 20mA
F
12
R
I-0
10
V
I—O
= 500V
Capacitance (Input-Output)
Output Rise-Fall Time (10-90%)
Common Mode Transient Immunity at
High Output Level
C
5
35
10000
pF
ns
V/µs
f = 1MHz
R = 510Ω, C = 50pFI = 13mA
L
I-O
t ,
t
r
f
L
F
CM
1000
1000
V
= 10V (peak),
(min) = 2V,
6
7
H
CM
V
O
R
L
= 510Ω, I = OmA
F
Common Mode Transient Immunity at
Low Output Level
CM
10000
V/µs
V
V
= 10V (peak),
(max) = 0.8V,
L
CM
O
R
= 510Ω, I = 1OmA
L
F
NOTES:
1.
2.
3.
4.
5.
6.
7.
Each channel
Measured between input pins shorted together and output pins shorted together.
It is essential that a bypass capacitor (.01 to 0.1µF ceramic) be connected from pin 1 to pin 4.
The t propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output pulse.
The t propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output pulse.
CM is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. V >2.0V).
CM is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. V < 0.8V).
plh
phl
h
l
o
o
RECOMMENDED OPERATING CONDITIONS:
PARAMETER
Input Current, Low Level Each Channel
Input Current, High Level Each Channel
Supply Voltage
SYMBOL
MIN
0
MAX
250
20
5.5
6
UNITS
µA
mA
V
I
FL
I
V
12.5
4.5
FH
C
Fan Out (TTL Load) Each Channel
Operating Temperature
N
°
T
A
-55
125
C
SELECTION GUIDE
PART NUMBER
PART DESCRIPTION
66056-011
Single Channel, commercial optocoupler
Dual Channel, commercial optocoupler
Single Channel, Mil-temp optocoupler tested over full military temperature range (-55 to +125 C)
Dual Channel, Mil-temp optocoupler tested over full military temperature range (-55 to +125 C)
Single Channel optocoupler tested over full military temperature range with 100% device screening
Dual Channel optocoupler tested over full military temperature range with 100% device screening
DSCC Dwg 8102802PX Dual channel optocoupler
66056-012
66056-001
66056-002
66056-101
66056-102
66056-103
°
°
°
°
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
www.micropac.com E-MAIL: optosales@micropac.com
3 - 35
MII [ Micropac Industries ]
