MIW5000 Series
Model Selection Guide
Model
Number
Input
Voltage
Output
Voltage
Output Current
Input Current
Reflected
Ripple
Current
mA (Typ.)
Efficiency
VDC
MIW5021
MIW5022
MIW5023
MIW5024
MIW5026
MIW5027
MIW5029
MIW5030
MIW5031
MIW5032
MIW5033
MIW5034
MIW5036
MIW5037
MIW5039
MIW5040
MIW5041
MIW5042
MIW5043
MIW5044
MIW5046
MIW5047
MIW5049
48
( 36 ~ 75 )
24
( 18 ~ 36 )
12
( 9 ~ 18 )
VDC
3.3
5
12
15
{12
{15
5.1
2.5
3.3
5
12
15
{12
{15
5.1
2.5
3.3
5
12
15
{12
{15
5.1
Max.
mA
3000
2000
833
666
{416
{333
2000
3000
3000
2000
833
666
{416
{333
2000
3000
3000
2000
833
666
{416
{333
2000
Min.
mA
300
200
83
66.6
{42
{33
200
300
300
200
83
66.6
{42
{33
200
300
300
200
83
66.6
{42
{33
200
@Max. Load
mA (Typ.)
1006
1004
957
968
957
968
1024
377
485
479
479
478
473
478
489
188
243
239
240
239
236
243
244
@No Load
mA (Typ.)
@Max. Load
% (Typ.)
82
83
87
40
60
86
87
86
83
83
85
87
87
87
88
87
87
83
85
87
87
87
88
87
87
20
40
10
40
Absolute Maximum Ratings
Parameter
Input Surge Voltage
( 1000 mS )
12VDC Input Models
24VDC Input Models
48VDC Input Models
Min.
-0.7
-0.7
-0.7
---
---
Max.
25
50
100
260
2,500
Unit
VDC
VDC
VDC
]
mW
Notes :
1. Specifications typical at Ta=+25], resistive load,
nominal input voltage, rated output current unless
otherwise noted.
2. Transient recovery time is measured to within 1%
error band for a step change in output load of 75%
to 100%.
3. Ripple & Noise measurement bandwidth is 0-20
MHz.
4. These power converters require a minimum output
loading to maintain specified regulation.
Lead Temperature (1.5mm from case for 10 Sec.)
Internal Power Dissipation
Exceeding the absolute maximum ratings of the unit could cause damage.
These are not continuous operating ratings.
Environmental Specifications
Parameter
Operating Temperature
Operating Temperature
Storage Temperature
Humidity
Cooling
Conducted EMI
Conditions
Ambient
Case
Min.
-40
-40
-40
---
Free-Air Convection
EN55022 Class A
Max.
+60
+90
+125
95
Unit
]
]
]
%
5. Operation under no-load conditions will not
damage these modules; however, they may not
meet all specifications listed.
6. All DC/DC converters should be externally fused
on the front end for protection.
7. Other input and output voltage may be available,
please contact factory.
8. Specifications subject to change without notice.
REV:0 2005/04
MINMAX
2
MINMAX [ MINMAX TECHNOLOGY CO., LTD. ]
