OUTPUT SPECIFICATIONS
Item
Output power
Line regulation
For Vin change of 1%
5V output
Load regulation
10% to 100% load
9V output
12V output
15V output
Output voltage accuracy
Temperature drift
Ripple & Noise*
Switching frequency
100% full load
20MHz Bandwidth
Full load,
nominal input
5V input
12V,24V input
150
35
50
10
8.3
6.8
6.3
Test conditions
Min
0.2
Typ
Max
2
±1.2
15
15
15
15
%
Units
W
Recommended testing and application circuit
If you want to further decrease the input/output
ripple, an
“LC”
filtering network may be connected
to the input and output ends of the DC/DC
converter, see (Figure 1).
Dual Output
L
L
Vin
Cin
+Vo
Cout
DC DC
GND
Single Output
L
L Cout
0V
-Vo
L
See tolerance envelope graph
0.03
250
%/°C
mVp-p
KHz
Vin
Cin
+Vo
Cout
DC DC
(Figure 1)
GND
0V
*Test ripple and noise by
“parallel
cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note: Dual output models unbalanced load:
±5%.
TYPICAL CHARACTERISTICS
It should also be noted that the inductance and
the frequency of the
“LC”
filtering network should
be staggered with the DC/DC frequency to avoid
mutual interference. However, the capacitance of
the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might
arise. For every channel of output, provided the
safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees
(Table 1).
EXTERNAL CAPACITOR TABLE (Table 1)
Vin
Dual
Cout
Cin
Single Cout
(VDC)
(uF)
Vout
(uF)
Vout
(uF)
(VDC)
(VDC)
5
4.7
5
10
4.7
±
5
12
24
-
2.2
1
-
9
12
15
4.7
2.2
1
Ambient Temperature
( C )
±
9
±
12
±
15
2.2
1
1
It’s not recommended to connect any external capacitor
in the application field with less than 0.5 watt output.
OUTLINE DIMENSIONS & PIN CONNECTIONS
First Angle Projection
10.40
(0.409)
0.50
(0.020)
4.90
(0.193)
(
Side View
)
RECOMMENDED FOOTPRINT
Top
view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
Output Voltage Regulation and Over-voltage
Protection Circuit
The simplest device for output voltage
regulation,
over-voltage
and
over-current
protection is a linear voltage regulator with
overheat protection that is connected to the input
or output end in series (Figure 2).
Dual Output
Vin
GND
Single Output
REG
REG
Single/Dual Ouput
1
2
8 9
11
16.65(0.656)
14.40(0.560)
+Vo
0V
17 16 15 14 13
(
Bottom View
)
17 16 15 14 13
DC DC
REG
-Vo
+Vo
2.54(0.100)
27.94(1.100)
32.30(1.272)
1 2
8 9
11
Vin
GND
REG
REG
DC DC
0V
FOOTPRINT DETAILS
10.30
(0.406)
(Figure 2)
Dual
Vin
GND
-Vo
0V
+Vo
NC
Pin
1
2
16.65(0.656)
Single
Vin
GND
NC
0V
Note:
Unit:mm(inch)
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin section tolerances: 0.10mm( 0.004inch)
General tolerances: 0.25mm( 0.010inch)
12
,
13
Others
+Vo
NC
NC: No connection
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection against
overload. The simplest method is to connect a
self-recovery fuse in series at the input end or add
a circuit breaker to the circuit.
No parallel connection or plug and play.
APPLICATION NOTE
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum
output load is not less than 10% of the full load, and that this product should
never be
operated under no load!
If the actual output power is very small, please connect a resistor
with proper resistance at the output end in parallel to increase the load, or use our
company’s products with a lower rated output power(G/H_D-1W Series)
Note:
1. All specifications measured at Ta=25°C, humidity<75%,
nominal input voltage and rated output load unless
otherwise specified.
2. Only typical models listed, other models may be
different, please contact our technical person for more
details.
3. Operation under minimum load will not damage the
converter; However, they may not meet all specification
listed.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
G_D-2W & H_D-2W
A/3-2008
Page 2 of 2
MORNSUN [ MORNSUN SCIENCE& TECHNOLOGY LTD. ]
