欢迎访问ic37.com |
会员登录 免费注册
发布采购

MC10H350P 参数 Datasheet PDF下载

MC10H350P图片预览
型号: MC10H350P
PDF下载: 下载PDF文件 查看货源
内容描述: PECL *到TTL转换器(只有+5 VDC电源) [PECL*to TTL Translator(+5 Vdc Power Supply Only)]
分类和应用: 转换器电平转换器驱动程序和接口锁存器接口集成电路光电二极管
文件页数/大小: 4 页 / 110 K
品牌: MOTOROLA [ MOTOROLA, INC ]
 浏览型号MC10H350P的Datasheet PDF文件第2页浏览型号MC10H350P的Datasheet PDF文件第3页浏览型号MC10H350P的Datasheet PDF文件第4页  
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
PECL* to TTL Translator
(+5 Vdc Power Supply Only)
The MC10H350 is a member of Motorola’s 10H family of high performance
ECL logic. It consists of 4 translators with differential inputs and TTL outputs.
The 3–state outputs can be disabled by applying a HIGH TTL logic level on the
common OE input.
The MC10H350 is designed to be used primarily in systems incorporating
both ECL and TTL logic operating off a common power supply. The separate
VCC power pins are not connected internally and thus isolate the noisy TTL VCC
runs from the relatively quiet ECL VCC runs on the printed circuit board. The
differential inputs allow the H350 to be used as an inverting or noninverting
translator, or a differential line receiver. The H350 can also drive CMOS with the
addition of a pullup resistor.
Propagation Delay, 3.5 ns Typical
MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Power Supply (VEE = Gnd)
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
Symbol
VCC
TA
Tstg
Rating
7.0
0 to +75
–55 to +150
–55 to +165
Unit
Vdc
°C
°C
°C
MC10H350
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
LOGIC DIAGRAM
9
3
4
5
6
11
12
13
14
VCC (+5.0 VDC) = PINS 1 AND 16
GND = PIN 8
2
ELECTRICAL CHARACTERISTICS
(VCC = 5.0 V
±5%)
(See Note 1)
TA = 0°C to 75°C
Characteristic
Power Supply Current
Input Current High
Input Current Low
Input Voltage High
Input Voltage Low
TTL
ECL
Pin 9
Others
Pin 9
Others
Pin 9
Pin 9
Symbol
ICC
IIH
IINH
IIL
IINL
VIH
VIL
VDIFF
VCM
Pins 3–6, 11–14
Output Voltage High
IOH = 3.0 mA
Output Voltage Low
IOL = 20 mA
Short Circuit Current
VOUT = 0 V
Output Disable Current High
VOUT = 2.7 V
Output Disable Current Low
VOUT = 0.5 V
VOH
VOL
IOS
IOZH
IOZL
2.7
–60
0.5
–150
50
–50
Vdc
Vdc
mA
µA
µA
Min
2.0
350
2.8
Max
20
12
20
50
–0.6
50
0.8
VCC
Unit
mA
µA
mA
µA
Vdc
Vdc
mV
Vdc
7
10
15
Differential Input Voltage (1)
Pins 3–6, 11–14 (1)
Voltage Common Mode
DIP
PIN ASSIGNMENT
ECL VCC
AOUT
AIN
AIN
BIN
BIN
BOUT
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
TTL VCC
COUT
CIN
CIN
DIN
DIN
DOUT
OE
(1) Common mode input voltage to pins 3–4, 5–6, 11–12, 13–14 must be between the values of 2.8
V and 5.0 V. This common mode input voltage range includes the differential input swing.
(2) For single ended use, apply 3.75 V (VBB) to either input depending on output polarity required.
Signal level range to other input is 3.3 V to 4.2 V.
(3) Any unused gates should have the inverting inputs tied to VCC and the non–inverting inputs tied
to ground to prevent output glitching.
(4) 1.0 V to 2.0 V w/50 pF into 500 ohms.
*Positive Emitter Coupled Logic
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
9/96
©
Motorola, Inc. 1996
2–57
REV 6