A100HI
Series
Ultra-High Isolation, 1.5W
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
•
1.5W Output Power
•
8,000 VDC Isolation
•
2 µA Leakage Current Max
•
Compact DIP Case
•
Single & Dual Outputs
•
Meets EN55022 Class A
•
1.0 MH MTBF
•
Industry Standard Pin-Out
Input
Parameter
Input Voltage Range
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Conditions
Min.
Typ.
5.0
12.0
15.0
Max.
5.5
13.2
16.5
0.5
1,000
Units
VDC
5 VDC Input
4.5
12 VDC Input 10.8
15 VDC Input 13.5
(Pi) Filter
A
mW
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation, (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Typ.
Max.
±4.0
±2.0
±1.5
40
50
15
±0.02
Units
%
%
%
mV P - P
mV P - P
mV rms
%
%/ºC
±2.0
Dual Output , Balanced Loads
±0.5
For Vin Change of 1%
±1.2
See Model Selection Guide
30
Over Line, Load & Temp.
120
±0.01
Continuous
General
Parameter
Isolation Voltage, Rated
Isolation Test Voltage
Leakage Current
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
Flash Tested For 1 Second
240 VAC, 60 Hz
500 VDC
100 kHz, 1V
Min.
8,000
8,800
Typ.
Max.
Units
VDC
VDC
µA
G
pF
kHz
2
10
10
50
15
100
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Ambient
Case
Min.
Typ.
Max.
+85
+95
+125
95
Units
ºC
ºC
ºC
%
-40
-40
-55
Free Air Convection
RH, Non-condensing
Physical
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T:
(781) 344-8226
F:
(781) 344-8481
E:
sales@micropowerdirect.com
W:
www.micropowerdirect.com
Case Size
Case Material
Weight
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
2.0
Typ.
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
5 VDC Input
12 VDC Input
15 VDC Input
1.5 mm From Case For 10 Sec
All Models
Min.
-0.7
-0.7
-0.7
Typ.
Max.
7.0
17.0
21.0
260
1,000
Units
VDC
º
C
mW
Caution:
Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
