Model Selection Guide
Model
Number
A1102RW
A1103RW
A1104RW
A1105RW
A1106RW
A1107RW
A1111RW
A1112RW
A1113RW
A1114RW
A1115RW
A1116RW
A1117RW
A1121RW
A1122RW
A1123RW
A1124RW
A1125RW
A1126RW
A1127RW
Voltage (VDC)
Nominal
12
12
12
12
12
12
24
24
24
24
24
24
24
48
48
48
48
48
48
48
Range
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
Input
Current (mA)
Full-Load
1,006
1,004
957
968
957
968
377
485
479
479
478
473
478
188
243
239
240
239
236
243
Output
Fuse Rating
Slow-Blow
(mA)
2,000
2,000
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
Reflected
Efficiency
Current
Ripple Voltage Current
(%, Typ)
(VDC) (mA, Max) (mA, Min)
No-Load Current
(mA, Typ)
40
40
40
40
40
40
20
20
20
20
20
20
20
10
10
10
10
10
10
10
60
60
60
60
60
60
40
40
40
40
40
40
40
40
40
40
40
40
40
40
3.3
5.0
12.0
15.0
±12.0
±15.0
2.5
3.3
5.0
12.0
15.0
±12.0
±15.0
2.5
3.3
5.0
12.0
15.0
±12.0
±15.0
3,000
2,000
833
666
±416
±333
3,000
3,000
2,000
833
666
±416
±333
3,000
3,000
2,000
833
666
±416
±333
300.0
200.0
83.0
66.6
±42.0
±33.0
300.0
300.0
200.0
83.0
66.6
±42.0
±33.0
300.0
300.0
200.0
83.0
66.6
±42.0
±33.0
82
83
87
86
87
86
83
85
87
87
87
88
87
83
85
87
87
87
88
87
Notes:
1. When measuring output ripple, it is recommended that an external 0.47 µF
ceramic capacitor be placed from the +Vout pin to the -Vout pin for single
output units and from each output to common for dual output units. For
noise sensitive applications, the use of 3.3 µF capacitors will reduce the
output ripple.
2. Transient recovery is measured to within a 1% error band for a load step
change of 75% to 100%.
3. Operation at no-load will not damage these units. However, they may not
meet all specifications.
4. Dual output units may be connected to provide a 24 VDC or 30 VDC output.
To do this, connect the load across the positive (+Vout) and negative (-Vout)
outputs and float the output common.
5. The converter should be connected to a low ac-impedance source. An
input source with a highly inductive impedance may affect the stability of
the converter. In applications where the converter output loading is high
and input power is supplied over long lines, it may be necessary to use a
capacitor on the input to insure start-up.
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz)
capacitor be mounted close to the converter. For 12V input units a 12 µF
is recommended, for 24V input units, a 4.7 µF; and for 48V units a 2.2 µF.
6. Models with 5.1 VDC outputs are available. Please contact the factory for
details.
7. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
2, 3
9
11
Single
-Vin
No Pin
NC
Dual
-Vin
Common
-Vout
Pin
14
16
22, 23
Single
+Vout
-Vout
+Vin
Dual
+Vout
Common
+Vin
NC: No Connection
Capacitive Load
Output
(VDC)
µF Max
2.5
3.3
5.0
5.1
12
820
15
470
±12
±220
±15
±150
2,200 2,200 2,200 2,200
Mechanical Notes:
•
All dimensions are typical in inches (mm)
•
Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
www.micropowerdirect.com
•
292 Page Street Ste D Stoughton, MA 02072
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
