Model Selection Guide
Model
Number
A301RW
A302RW
A303RW
A304RW
A305RW
A306RW
A307RW
A311RW
A312RW
A313RW
A314RW
A315RW
A316RW
A317RW
A321RW
A322RW
A323RW
A324RW
A325RW
A326RW
A327RW
A331RW
A332RW
A333RW
A334RW
A335RW
A336RW
A337RW
Voltage (VDC)
Nominal
5
5
5
5
5
5
5
12
12
12
12
12
12
12
24
24
24
24
24
24
24
48
48
48
48
48
48
48
Range
4.5 - 9.0
4.5 - 9.0
4.5 - 9.0
4.5 - 9.0
4.5 - 9.0
4.5 - 9.0
4.5 - 9.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
Input
Current (mA)
Full-Load
566
685
779
779
694
800
800
223
267
305
305
271
313
313
109
132
149
149
132
152
152
55
66
75
75
65
75
75
Output
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
700
700
350
350
350
350
350
350
350
135
135
135
135
135
135
135
Reflected
Efficiency
Current
Ripple Voltage Current
(%, Typ)
(VDC) (mA, Max) (mA, Min)
No-Load Current
(mA, Typ)
40
40
40
40
40
40
40
20
20
20
20
20
20
20
5
5
5
5
5
5
5
3
3
3
3
3
3
3
100
100
100
100
100
100
100
30
30
30
30
30
30
30
15
15
15
15
15
15
15
10
10
10
10
10
10
10
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
600.0
500.0
250.0
200.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
±250.0
±125.0
±100.0
60.0
50.0
25.0
20.0
±25.0
±12.5
±10.0
60.0
50.0
25.0
20.0
±25.0
±12.5
±10.0
60.0
50.0
25.0
20.0
±25.0
±12.5
±10.0
60.0
50.0
25.0
20.0
±25.0
±12.5
±10.0
70
73
77
77
72
75
75
74
78
82
82
77
80
80
76
79
84
84
79
82
82
76
79
84
84
80
84
84
Notes:
1. When measuring output ripple, it is recommended that an external 0.47
µF
ceramic ca-
pacitor be placed from the +Vout pin to the -Vout pin for single output units and from
each output to common for dual output units. For noise sensitive applications, the use
of 3.3
µF
capacitors will reduce the output ripple.
2. Transient recovery is measured to within a 1% error band for a load step change of 75%
to 100%.
3. Operation at no-load will not damage these units. However, they may not meet all
specifications.
4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To
do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and
float the output common.
5. The converter should be connected to a low ac-impedance source. An input source with
a highly inductive impedance may affect the stability of the converter. In applications
where the converter output loading is high and input power is supplied over long lines,
it may be necessary to use a capacitor on the input to insure start-up.
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be mounted
close to the converter. For 5V input units a 8.2
µF
is recommended, for 12V input units,
a 3.3
µF;
and for 24V & 48V units a 2.2
µF.
6. It is recommended that a fuse be used on the input of a power supply for protection.
See the table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
2, 3
9
11
Single
-Vin
No Pin
NC
Dual
-Vin
Common
-Vout
Pin
14
16
22, 23
Single
+Vout
-Vout
+Vin
Dual
+Vout
Common
+Vin
NC: No Connection
Capacitive Load
Single Output
4,000
µF
Max
Dual Output
±1,000
µF
Max
Mechanical Notes:
•
All dimensions are typical in inches (mm)
•
Tolerance x.xx = ±0.01 (±0.25)
•
Leads are gold plated for improved
solderability.
MicroPower Direct
www.micropowerdirect.com
•
292 Page Street Ste D Stoughton, MA 02072
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
