D100VHI
Series
Miniature, 1W SIP
Ultra-High Isolation
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
•
1W Output Power
•
6.0 kVDC Isolation
•
Miniature SIP Case
•
Single & Dual Outputs
•
Miniature SIP Case
•
12 Standard Models
•
2.0 MH MTBF
•
Industry Standard Pin-Out
Input
Parameter
Input Voltage Range
Input Filter
Reverse Polarity Input Current
Conditions
5 VDC Input
12 VDC Input
Min.
4.5
10.8
Typ.
5.0
12.0
Max.
5.5
13.2
0.3
Conditions
Dual Output , Balanced Loads
For Vin Change of 1%
Min.
Typ.
±1.0
±0.1
±1.2
100
Over Line, Load & Temp.
120
±0.01
Momentary (0.5 Sec.)
Conditions
60 Seconds
Flash Tested For 1 Sec
500 VDC
100 kHz, 1V
50
Conditions
Ambient
Case
Min.
-40
-40
-40
Free Air Convection
RH, Non-condensing
95
%
Min.
6,000
6,600
10
15
80
Typ.
+25
20
100
Max.
+70
+90
+125
Typ.
Max.
Units
VDC
VDC
GΩ
pF
kHz
Units
°C
°C
°C
±0.02
Max.
±3.0
±1.0
±1.5
150
200
5
Units
VDC
Internal Capacitor
A
Units
%
%
%
mV P - P
mV P - P
mV rms
%
%/°C
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
See Model Selection Guide
RoHS Compliant
General
Parameter
Isolation Voltage
Isolation Test Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Cooling
Humidity
Physical
Case Size
Case Material
Weight
0.87 x 0.49 x 0.30 Inches (22.0 x 12.5 x 7.5 mm)
Non-Conductive Black Plastic (UL94-V0)
0.13 Oz (3.9g)
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Conditions
5 VDC Input
12 VDC Input
1.5 mm From Case For 10 Sec
All Models
Min.
2.0
Min.
-0.7
-0.7
Typ.
Max.
9.0
18.0
260
650
Typ.
Max.
Units
MHours
Units
VDC
°C
mW
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Caution:
Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
MPD [ MICROPOWER DIRECT, LLC ]
