High-Speed 32-bit Digital
Pattern I/O and Handshaking
Data Lines
Bus
Interface
Internal
FIFOs
PCI, PXI, CPCI, PCMCIA, ISA I/O Channel
EEPROM
Counters
and
Timers
Clock
Selection
Request
Processing
Digital I/O Connector
MITE PCI,
PCMCIA, or AT
Plug and Play
Interface
Onboard
Scarab
Memory
(for 6534 only)
Data Latches
and
Drivers
Handshaking
and
Control
Data Lines
(32)
Digital I/O Devices
Driver Software
With NI-DAQ driver software, you can configure your devices
interactively, write custom programs, and perform digital I/O
transfers easily. With NI-DAQ, the NI 6533 and NI 6534 devices
are software-compatible, providing a seamless upgrade path.
Sharing clocks and triggers between NI 653x and other
measurement devices is also greatly simplified. To get you started
with your application quickly, NI-DAQ includes numerous example
programs for LabVIEW and other ADEs.
Signal Names
DIOAx, DIOBx, DIOCx, DIODx
REQ1, REQ2, ACK1, ACK2
STOPTRIG1, STOPTRIG2
PCLK1, PCLK2
CPULL, DPULL
Signal Types
data
control
control
control
power-up
Signal Descriptions
Digital input/output lines
Handshaking, timing
and trigger lines
Trigger lines
Handshaking timing lines
Lines determine power-up states
DMA/
Interrupt
Requests
Control
Lines (8)
DAQ-DIO
20 MHz
Oscillator
RTSI Interface
(PCI/PXI/AT only)
RTSI Bus (PCI/PXI/AT only)
Figure 1. NI 653x Hardware Block Diagram
Messaging
You can develop event-driven application programs with NI 653x devices
by programming them to generate a message when conditions you
specify are met. The messages can be generated when a specified
number of bytes have been transferred, when a specified input pattern
is matched, or when a measurement operation completes.
Onboard Memory
NI 6534 devices provide two groups of 32 MB of onboard memory, so
you can perform pattern I/O at deterministic high rates as long as the
patterns can fit in one of these memory locations. To improve system
performance for repetitive pattern output applications, you can load
your patterns into the onboard memory once and then output them
repeatedly, without reloading them across the computer bus.
Table 2. Signal Names and Descriptions
DAQ and Signal Conditioning
Related Products
High-Speed Digitizers ......................................see page 440
Arbitrary Waveform and Function Generators......see page 467
Multifunction Data Acquisition ........................see page 188
DMA Control Circuitry
NI 653x devices for PCI and PXI use the National Instruments MITE PCI
interface. The MITE provides bus-master operation, PCI burst transfers,
and high-performance DMA controllers for fast, continuous, scatter-
gather DMA.
Ordering Information
NI PCI-6534* ........................................................778287-01
NI PXI-6534* ........................................................778288-01
DIOD7
GND
DIOD4
DIOD3
GND
DIOD0
DIOC7
GND
DIOC4
DIOC3
GND
DIOC0
DIOB7
DIOB6
GND
RGND
GND
DIOB1
DIOB0
DIOA7
GND
DIOA4
DIOA3
GND
DIOA0
REQ2
ACK2
STOPTRIG2
PCLK2
PCLK1
STOPTRIG1
ACK1
REQ1
+5 V
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
GND
DIOD6
DIOD5
GND
DIOD2
DIOD1
GND
DIOC6
DIOC5
GND
DIOC2
DIOC1
RGND
GND
DIOB5
DIOB4
DIOB3
DIOB2
GND
GND
DIOA6
DIOA5
GND
DIOA2
DIOA1
RGND
GND
GND
CPULL
GND
DPULL
GND
GND
RGND
Multidevice Synchronization
All NI 653x devices except the DAQCard-6533 use
the PXI trigger bus or RTSI Bus to send and
receive clock and trigger signals to and from other
devices in your system. Using these buses, you
can create synchronized systems with large
numbers of digital I/O lines and systems in which
digital I/O is synchronized with other types of
measurements. The PXI-653x modules feature
phase-lock loop (PLL) circuitry
synchronize with other PLL devices.
to
tightly
NI PCI-DIO-32HS ..................................................777314-01
NI PXI-6533 ..........................................................777429-01
NI DAQCard-6533.................................................777315-01
NI AT-DIO-32HS* ..................................................777313-01
Includes NI-DAQ driver software.
*Windows only
For information on extended warranty and value added
services, see page 20.
Recommended Configurations
Family
NI 6534
NI 6533
DAQ Device
PCI-6534
PXI-6534
PCI-DIO-32HS
PXI-6533
DAQCard-6533
AT-DIO-32HS
Accessory
SCB-68 (776844-01)
TB-2715 (778242-01)
SCB-68 (776844-01)
TB-2715 (778242-01)
SCB-68 (776844-01)
SCB-68 (776844-01)
Cable
SH68-68-D1 (183432-01)
N/A*
SH68-68-D1 (183432-01)
N/A*
PSHR68-68-D1 (777420-01)
SH68-68-D1 (183432-01)
I/O Connector and Power-Up States
All digital I/O is through a 68-pin cable connector.
See pin assignments and descriptions in
Figure 2 and Table 2. You can independently
select the power-on state for the control and
data lines through the use of CPULL and
DPULL, respectively.
*TB-2715 plugs directly into device; no cable required.
See page 384 for accessory and cable information.
Figure 2. NI 653x I/O Connector
National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • info@ni.com • ni.com
379
NI [ NATIONAL INSTRUMENTS CORPORATION ]
