欢迎访问ic37.com |
会员登录 免费注册
发布采购

PCF1A471MCL1GS 参数 Datasheet PDF下载

PCF1A471MCL1GS图片预览
型号: PCF1A471MCL1GS
PDF下载: 下载PDF文件 查看货源
内容描述: 导电性高分子铝固体电解电容器 [CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS]
分类和应用: 电容器
文件页数/大小: 2 页 / 108 K
品牌: NICHICON [ NICHICON CORPORATION ]
 浏览型号PCF1A471MCL1GS的Datasheet PDF文件第2页  
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
Chip Type, Standard
series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Category Temperature Range
Rated Voltage Range
Performance Characteristics
– 55 ~ +105°C
2.5 ~ 25V
± 20% at 120Hz, 20°C
Not more than value of Standard ratings at 120Hz, 20°C
Not more than value of Standard ratings at 100kHz, 20°C
Rated Capacitance Range
6.8 ~ 1500µF
Capacitance Tolerance
tan
δ
ESR (
1)
2)
Leakage Current (
Not more than value of Standard ratings.
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
1.25
1.25
(100kHz)
After 2 minute's application of rated voltage.
20°C
Characteristics of Temperature
Impedance Ratio
Endurance
After 2000 hours' application of rated voltage
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan
δ
ESR
( 1)
Leakage current ( 2)
Capacitance change
tan
δ
ESR
( 1)
Leakage current ( 2)
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Damp Heat
After 1000 hours' application of rated voltage
at 60°C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
In the case of peak temp, less than 250°C,
reflow soldering shall be within two times.
In the case of peak temp, less than 260°C,
reflow soldering shall be once.
Measurement for solder temperature profile shall
be made at the capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Capacitance change
tan
δ
ESR
( 1)
Leakage current ( 2)
Within ± 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
Marking
1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Type numbering system (Example : 6.3V 150µF)
C±0.2
0.5 MAX.
Negative
A±0.2
Voltage
V
Code
2.5
e
4
g
6.3
j
10
A
16
C
20
D
25
E
Lot No.
B
D + 0.5 MAX.
Plastic platform
0.3 MAX.
Positive
CF
150
j
6X1
B±0.2
Series
Voltage
( j:6.3v)
L
+0.1
-0.4
H
(mm)
Size
φD
L
A
B
C
E
H
φ6.3
×
6L
6.3
5.9
7.3
6.6
6.6
2.1
0.5 ~ 0.8
φ8
×
7L
8.0
6.9
9.0
8.3
8.3
3.2
0.8 ~ 1.1
φ10
×
8L
10.0
7.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
φ10
×
10L
10.0
9.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
Dimension table in next page.
E
CAT.8100V