欢迎访问ic37.com |
会员登录 免费注册
发布采购

PCJ0E391MCL1GS 参数 Datasheet PDF下载

PCJ0E391MCL1GS图片预览
型号: PCJ0E391MCL1GS
PDF下载: 下载PDF文件 查看货源
内容描述: 导电性高分子铝固体电解电容器 [CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS]
分类和应用: 电容器
文件页数/大小: 2 页 / 65 K
品牌: NICHICON [ NICHICON CORPORATION ]
 浏览型号PCJ0E391MCL1GS的Datasheet PDF文件第2页  
CONDUCTIVE POLYMER
ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ
Higher Capacitance, Low ESR
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105
°C.
SMD type : Lead free reflow soldering condition at 260°C peak correspondence.
Adapted to the RoHS directive (2002/95/EC).
CJ
Higher
Capacitance,
Low ESR
CF
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
tan
δ
ESR ( 1)
Leakage Current ( 2)
–55 ~ +105°C
2.5 ~ 16V
39 ~ 2700µF
±
20% at 120Hz, 20°C
Not more than value of Standard ratings
Not more than value of Standard ratings
Not more than value of Standard ratings.
1.25
1.25
Capacitance change
tan
δ
ESR ( 1)
Leakage current ( 2)
Within
±
20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
(100kHz)
at 120Hz, 20°C
at 100kHz, 20°C
After 2 minute's application of rated voltage.
20°C
Performance Characteristics
Characteristics of Temperature Z+105°C / Z + 20°C
Impedance Ratio
Z - 55°C / Z + 20°C
After 2000 hours' application of rated voltage
Endurance
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
After 1000 hours' application of rated voltage
Damp Heat
at 60°C 90%RH, capacitors meet the specified
value for life characteristics listed at right.
Capacitance change
tan
δ
ESR ( 1)
Leakage current ( 2)
Within
±
20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
In the case of peak temp, less than 250°C,
Resistance to
Soldering Heat
reflow soldering shall be within two times.
In the case of peak temp, less than 260°C,
reflow soldering shall be once.
Measurement for solder temperature profile
shall be made at the capacitor top and the
terminal.
Marking
Navy blue print on the case top.
Capacitance change
tan
δ
ESR ( 1)
Leakage current ( 2)
Within
±
10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
1 ESR measurements should be made at a point on the terminal nearest where the ternimals protrude through the plastic platform.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.