CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF
Radial Lead Type, Standard
series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Category Temperature Range
Rated Voltage Range
Performance Characteristics
– 55 ~ +105°C
2.5 ~ 16V
± 20% at 120Hz, 20°C
Not more than value of Standard ratings at 120Hz, 20°C
Not more than value of Standard ratings at 100kHz, 20°C
Rated Capacitance Range
270 ~ 1000µF
Capacitance Tolerance
tan
δ
ESR (
1)
2)
Leakage Current (
Not more than value of Standard ratings.
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
1.25
1.25
(100kHz)
After 2 minute's application of rated voltage.
20°C
Characteristics of Temperature
Impedance Ratio
Endurance
After 2000 hours' application of rated voltage
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan
δ
ESR (
1)
2)
Leakage current (
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Damp Heat
After 1000 hours' application of rated voltage
at 60°C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
Peak temp. is 265°C, within 10 sec.
Measurement for solder temperature profile shall
be made at a point on the terminal nearest where
the terminals protrude through the soldering side
of PC board.
Navy blue print on the case top
Capacitance change
tan
δ
ESR (
1)
2)
Leakage current (
Resistance to
Soldering Heat
Capacitance change
tan
δ
ESR (
1)
2)
Leakage current (
Within ± 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
Marking
1 ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Type numbering system (Example : 4V 560
µ
F)
Laminated Case
Silvered lead Wire
Voltage(g:4V)
φ
D+0.5 MAX.
Taping code
P ±0.5
6 X 1
5 6 0
L F
g
φ
d
Series
Lot. No.
L+0.5MAX.
15MIN
4MIN
(mm)
Size
φD
L
P
φd
φ8
×
9L
8.0
8.5
3.5
0.6
φ8
×
12L
φ10
×
13L
8.0
10.0
11.5
12.5
3.5
5.0
0.6
0.6
Voltage
V
Code
2.5
e
4
g
6.3
j
10
A
16
C
Dimension table in next page.
CAT.8100V
NICHICON [ NICHICON CORPORATION ]
