欢迎访问ic37.com |
会员登录 免费注册
发布采购

MSM511664C-70JS 参数 Datasheet PDF下载

MSM511664C-70JS图片预览
型号: MSM511664C-70JS
PDF下载: 下载PDF文件 查看货源
内容描述: 65536字×16位动态RAM :快速页面模式类型(字节写入) [65,536-Word X 16-Bit DYNAMIC RAM : FAST PAGE MODE TYPE (BYTE WRITE)]
分类和应用: 存储内存集成电路光电二极管动态存储器
文件页数/大小: 16 页 / 238 K
品牌: OKI [ OKI ELECTRONIC COMPONETS ]
 浏览型号MSM511664C-70JS的Datasheet PDF文件第4页浏览型号MSM511664C-70JS的Datasheet PDF文件第5页浏览型号MSM511664C-70JS的Datasheet PDF文件第6页浏览型号MSM511664C-70JS的Datasheet PDF文件第7页浏览型号MSM511664C-70JS的Datasheet PDF文件第9页浏览型号MSM511664C-70JS的Datasheet PDF文件第10页浏览型号MSM511664C-70JS的Datasheet PDF文件第11页浏览型号MSM511664C-70JS的Datasheet PDF文件第12页  
¡ Semiconductor
Notes:
MSM511664C/CL
1. A start-up delay of 100
µs
is required after power-up, followed by a minimum of eight
initialization cycles (RAS-only refresh or
CAS
before
RAS
refresh) before proper device
operation is achieved.
2. The AC characteristics assume t
T
= 5 ns.
3. V
IH
(Min.) and V
IL
(Max.) are reference levels for measuring input timing signals.
Transition times (t
T
) are measured between V
IH
and V
IL
.
4. This parameter is measured with a load circuit equivalent to 1 TTL load and 50 pF.
5. Operation within the t
RCD
(Max.) limit ensures that t
RAC
(Max.) can be met.
t
RCD
(Max.) is specified as a reference point only. If t
RCD
is greater than the specified
t
RCD
(Max.) limit, then the access time is controlled by t
CAC
.
6. Operation within the t
RAD
(Max.) limit ensures that t
RAC
(Max.) can be met.
t
RAD
(Max.) is specified as a reference point only. If t
RAD
is greater than the specified
t
RAD
(Max.) limit, then the access time is controlled by t
AA
.
7. t
OFF
(Max.) and t
OEZ
(Max.) define the time at which the output achieves the open
circuit condition and are not referenced to output voltage levels.
8. t
RCH
or t
RRH
must be satisfied for a read cycle.
9. t
WCS
, t
CWD
, t
RWD
, t
AWD
and t
CPWD
are not restrictive operating parameters. They are
included in the data sheet as electrical characteristics only. If t
WCS
t
WCS
(Min.), then
the cycle is an early write cycle and the data out will remain open circuit (high
impedance) throughout the entire cycle. If t
CWD
t
CWD
(Min.) , t
RWD
t
RWD
(Min.),
t
AWD
t
AWD
(Min.) and t
CPWD
t
CPWD
(Min.), then the cycle is a read modify write
cycle and data out will contain data read from the selected cell; if neither of the above
sets of conditions is satisfied, then the condition of the data out (at access time) is
indeterminate.
10. These parameters are referenced to the
CAS
leading edge in an early write cycle, and
to the
WE
leading edge in an
OE
control write cycle, or a read modify write cycle.
8/16