Specifications
■
Characteristics
Operating speed
Operating frequency
Contact resistance
1 to 500 mm/second (pin plunger models)
Mechanical: 200 operations per minute max.
Electrical: 30 operations per minute max.
General Purpose: 30 mΩ max. (Standard force versions)
50 mΩ max. (Low force versions)
Microload:
100 mΩ max.
100 MΩ min. at 500
VDC
600
VAC,
50/60 Hz for 1 minute between terminals of same polarity
1,500
VAC,
50/60 Hz for 1 minute between current-carrying metal parts and ground, and between each
terminal and non-current-carrying metal parts
Malfunction: 10 to 55 Hz, 1.5 mm double amplitude
Destruction: 1,000 m/s
2
(approx. 100G) max.
Malfunction: 300 m/s
2
(approx. 30 g min.) max.
IEC IP40
Class I
175
-25° to 65°C (at 60% RH) with no icing
85% max. (for 5° to 35°C)
Insulation resistance
Dielectric strength (See note 2)
Vibration resistance (See note 3)
Shock resistance (See note 3)
Degree of protection
Degree of protection against
electric shock
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating Humidity
Service life
Mechanical: 1 million operations min. at 60 operations/minute.
(Consult Omron for test conditions)
Electrical: 30,000 operations min. at 30 operations/minute.
Weight
Approx. 0.5 g (pin plunger models)
Note: 1.
Data shown are of initial value.
2.
The dielectric strength shown in the table indicates a value for models with a separator.
3.
For pin plunger models, the values are measured at the free position and total travel position. For the lever models, they are measured
at the total travel position.
■
Ratings
Rated Voltage
Resistive load
Microvoltage/current (D2F-01 models)
Low force
125
VAC
30
VDC
—
0.1 A
Standard
—
0.1 A
General-purpose (D2F models)
Low force
1A
0.5 A
Standard
3A
2A
Note: 1.
When using an inductive load or motor load, consult OMRON.
2.
The ratings apply under the following test conditions: Ambient Temperature = 20
±
2
°
C, Ambient Humidity = 65
±
5%, Operating frequency = 30 operations/min.
■
Approvals
UL Recognized, CSA Certified
D2F
Rated voltage
125
VAC
30
VDC
Standard
Force
3A
2A
Low Force
1A
0.5 A
D2F-01
---
0.1 A
■
Contact Specifications
Item
Specification
Material
Gap
(Standard value)
Minimum Applicable Load
(See note)
D2F
Crossbar
Silver alloy
0.25 mm
100 mA at 5
VDC
1 mA at 5VDC
Gold alloy
D2F-01
Note:
The rated values approved by each of the safety standards
(e.g.UL,CSA) may be different from the performance
character-
istics individually defined in this catalog.
Note:
Minimum applicable loads are indicated by
N
standard
reference values. This value represents the failure rate at a
60% (λ
60
) reliability level (JIS C5003).
The equation
λ
60
=0.5 x 10
-6
/operations indicates that a failure
rate of 1/2,000,000 operations can be expected at a reliability
level of 60%.
32
Snap Action Switch
D2F
OMRON [ OMRON ELECTRONICS LLC ]
