D2VW-01L1-1HS 参数 Datasheet PDF下载

Specifications

■

Characteristics

Model

Operating speed

Operating frequency

Insulation resistance

Contact resistance

Dielectric strength (See note 2)

D2VW-01

0.1 mm to 1 m/s (at pin plunger)

Mechanical: 300 operations/minute max.

Electrical: 30 operations/minute max.

100 MΩ min. (at 500 VDC)

50 mΩ max. (100 mΩ max. for molded lead wire models)

1,000 VAC, 50/60 Hz for 1 min. between terminals of the same polarity

1,500 VAC, 50/60 Hz for 1 min. between each current-carrying metal parts and ground, and

between each terminal and non-current-carrying metal parts.

Malfunction: 10 to 55 Hz, 1.5 mm double amplitude

Destruction: 1,000 m/s

2

(approx. 100G) max.

Malfunction: 300 m/s

2

(approx. 30G) max.

IEC IP67 (excluding the terminals on terminal models).

Class I

175

-40° to 85°C (at 60% RH max.) with no icing

95% max. (for 5°C to 35°C)

Mechanical

Electrical

Weight

10,000,000 operations min. at 60 operations per minute

1,000,000 operations min. at 30 ops. per minute. 100,000 operations min. at 30 ops. per minute

Approx. 7g (pin plunger models without wires)

D2VW-5

Vibration resistance (See note 3)

Shock resistance (See note 3)

Degree of protection

Degree of protection against electric shock

Proof tracking index (PTI)

Ambient operating temperature

Ambient operating humidity

Life expectancy

Note: 1.

Data shown are of initial value.

2.

The dielectric strength shown is measured using a separator between the switch and metal mounting plate.

3.

For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, the values

apply at the total travel position.

4.

The operating temperature of the lead wire (AV0.75f) for non-UL/CSA molded lead wire models is between -40 to 85°C.

■

Ratings

(reference values)

D2VW-5

Rated Voltage

NC

125 VAC

250 VAC

30 VDC

125 VDC

D2VW-01

Rated Voltage

NC

125 VAC

30 VDC

0.1 A

0.1 A

Non-inductive load

Resistive load

NO

—

—

NC

Lamp load

NO

—

—

Inductive load

NC

NO

—

—

NC

Inductive load

Motor load

NO

5A

5A

5A

0.4 A

Non-inductive load

Resistive load

NO

0.5 A

0.5 A

3A

0.1 A

NC

Lamp load

NO

4A

4A

4A

0.4 A

Inductive load

NC

NO

—

—

—

—

NC

Inductive load

Motor load

NO

Note: 1.

The resistive load ratings apply under the following test conditions:

Ambient Temperature = 20±2°C, Ambient Humidity = 65±5%, Operating frequency = 30 operations/min.

2.

The above current ratings are the values of the steady-state current.

3.

Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC).

4.

Lamp load has an inrush current of 10 times the steady-state current.

5.

Rating for UL/CSA approval is as follows (See “Approved Standards” section):

D2VW-01

D2VW-5

0.1A @ 125 VAC

0.1A @ 30 VDC

3A @ 125 VAC, 250 VAC

208

Sealed Snap Action Switch

D2VW