LM311 LM211
MAXIMUM RATINGS
(TA = +25°C, unless otherwise noted.)
Rating
Total Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Input Differential Voltage
Input Voltage (Note 2)
Voltage at Strobe Pin
Power Dissipation and Thermal Characteristics
Plastic DIP
Derate Above TA = +25°C
Operating Ambient Temperature Range
Operating Junction Temperature
Storage Temperature Range
Symbol
VCC +VEE
VO –VEE
VEE
VID
Vin
–
PD
1/θJA
TA
TJ(max)
Tstg
–25 to +85
+150
–65 to +150
LM211
36
50
30
±30
±15
VCC to VCC–5
LM311
36
40
30
±30
±15
VCC to VCC–5
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mW
mW/°C
0 to +70
+150
–65 to +150
°C
°C
°C
625
5.0
ELECTRICAL CHARACTERISTICS
(VCC = +15 V, VEE = –15 V, TA = 25°C, unless otherwise noted [Note 1].)
LM211
Characteristic
Ch
i i
Input Offset Voltage (Note 3)
RS
≤
50 kΩ, TA = +25°C
RS
≤
50 kΩ, Tlow
≤
TA
≤
Thigh*
Input Offset Current (Note 3) TA = +25°C
Tlow
≤
TA
≤
Thigh*
Input Bias Current TA = +25°C
Tlow
≤
TA
≤
Thigh*
Voltage Gain
Response Time (Note 4)
Saturation Voltage
VID
≤
–5.0 mV, IO = 50 mA, TA = 25°C
VID
≤–10
mV, IO = 50 mA, TA = 25°C
VCC
≥
4.5 V, VEE = 0, Tlow
≤
TA
≤
Thigh*
VID
6
≤6.0
mV, Isink
≤
8.0 mA
VID
6
≤10
mV, Isink
≤
8.0 mA
Strobe ”On” Current (Note 5)
Output Leakage Current
VID
≥
5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID
≥
10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID
≥
5.0 mV, VO= 35 V, Tlow
≤
TA
≤
Thigh*
Input Voltage Range (Tlow
≤
TA
≤
Thigh*)
Positive Supply Current
Negative Supply Current
* Tlow
LM311
Max
3.0
4.0
10
20
100
150
–
–
1.5
–
0.4
–
–
10
–
0.5
+13.0
+6.0
–5.0
Min
–
–
–
–
–
–
40
–
–
–
–
–
–
–
–
–
–14.5
–
–
Typ
2.0
–
1.7
–
45
–
200
200
–
0.75
–
0.23
3.0
–
0.2
–
–14.7 to
13.8
+2.4
–1.3
Max
7.5
10
50
70
250
300
–
–
–
1.5
–
0.4
–
–
50
–
+13.0
+7.5
–5.0
mA
nA
nA
µA
V
mA
mA
nA
nA
V/mV
ns
V
Unit
U i
mV
Symbol
S b l
VIO
Min
–
–
Typ
0.7
–
1.7
–
45
–
200
200
0.75
–
0.23
–
3.0
0.2
–
0.1
–14.7 to
13.8
+2.4
–1.3
IIO
IIB
AV
–
–
–
–
40
–
VOL
–
–
–
–
IS
–
–
–
–
VICR
ICC
IEE
–14.5
–
–
= –25°C for LM211
Thigh = +85°C for LM211
= 0°C for LM311
= +70°C for LM311
NOTES:
1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to
±15
V supplies.
2. This rating applies for
±15
V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30 V below the positive supply, whichever is less.
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus,
these parameters define an error band and take into account the ”worst case” effects of voltage gain and input impedance.
4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.
5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
2
MOTOROLA ANALOG IC DEVICE DATA
ONSEMI [ ON SEMICONDUCTOR ]
